2012 Chrysler 200 Limited on 2040-cars

Auto blog

Fiat and UAW back at negotiating table over Chrysler stake

We knew there'd be no Chrysler IPO before the end of this year, but Fiat is determined to get the best run going into 2014 and is back at the poker table with the UAW. The delay was said to be Chrysler's desire to clean up a tax issue with the IRS; turns out that also bought the carmaker time to try and close a deal for the UAW's 48.5-percent stake in the company before the IPO happens.
Whereas the price Chrysler was willing to pay was once more than $1 billion under the UAW's asking price, the gap has closed to just $800 million of late. A recent valuation of the company at $10 billion - a valuation the UAW has disputed - means Fiat would be looking to pay about $4.2 billion instead of the $5 billion that the UAW seeks. But the UAW needs to hold out for the highest amount it can get because its pension obligations through the Voluntary Employee Benefit Association (VEBA) are $3.1 billion greater than the VEBA's assets, which include the Chrysler stake.
There's a clause in the agreement that Fiat can buy the VEBA shares for $6 billion, but Fiat CEO Sergio Marchionne has said that the UAW "should buy a ticket for the lottery" if they even want $5 billion. The UAW, though, has more time to wait; it's Fiat that wants access to Chrysler's $11.9-billion war chest and that would like to avoid the risk of paying the full $6 billion for the UAW share if the float really takes off. With other valuations of Chrysler as high as $19 billion, a hot IPO could make that $6 billion look like a bargain.

Mopar opening Custom Shop at Cobo

While other automakers have been streamlining their brand portfolio, the Chrysler Group has shown no such signs. It's got the Dodge, Chrysler and Jeep brands, plus Fiat, and it recently broke out its SRT and Ram nameplates into their own brands. And you can bet each will have its own presence at the Detroit Auto Show this year. But don't forget Mopar. The company's performance parts division is getting its own display at Cobo this year, and it'll be the largest in the brand's history.
The Mopar Custom Shop is poised to take up 5,500 square-feet of Cobo floor space, further expanding on last year's Mopar Garage. If the image above offers any indication, the show stand will include a Dodge Challenger, SRT Viper, Fiat 500L, Jeep Wrangler, Jeep Cherokee, Ram 3500 and what looks like (but isn't identified in the press release below as) a Chrysler 200 (which may be replaced by a 2014 model), all augmented with Mopar parts and accessories.
Visitors will also be able to use pre-programmed iPads to configure Chrysler Group vehicles with a wide range of accessories - a portfolio that grows by 1,500 new parts every year and tops over 100 add-ons for every new vehicle Chrysler launches.

This forgotten Chrysler was its bid for Humvee contract

Today, the Humvee might be as associated with the dead automotive brand from General Motors as it is with the hard-working truck that has long served as one of the backbone vehicles of America's military. But Autoline host John McElroy is showing off a practically unknown part of the model's story by digging out some old photos from his personal archive.
The High Mobility Multipurpose Wheeled Vehicle project, better known today as the Humvee, can be traced back to a US Department of Defense request for bids to build a new military truck. According to McElroy, he was invited to the Chrysler proving grounds in 1981 to check out the bid from the brand's defense division. The company's concept was that it might be able to build an inexpensive, capable vehicle by using off-the-shelf parts.
The angular body panels gave the truck a look almost like a modern, stealth vehicle. However, the flat look was actually just to make the tooling as cheap as possible to produce. Still, this Chrysler looked surprisingly futuristic for the early '80s. It's actually not too far away from the famous Lamborghini LM002, itself intended as a possible military-spec machine.