2004 Chevrolet Trailblazer Lt Sport Utility 4-door 4.2l Damaged, Repairable. on 2040-cars

Auto blog

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck

Corvette Z06 and Viper TA square off at the strip

There are many long-standing grudge matches among automobiles: 911 vs GT-R, Mustang vs Camaro, Ferrari vs Lamborghini... but as far as high-end American metal goes, it doesn't get much more legendary than Viper vs 'Vette. So after Chevy released the new Corvette Z06, we knew it was only a matter of time before it would have to square off against the Viper TA. And what better place to pit these two parallel pillars of American performance than on the drag strip? Fortunately that's just what we have here. In one corner, the 2014 Dodge Viper TA, with its 8.4-liter V10 pumping out 640 horsepower and 600 pound-feet of torque. In the other, the 2015 Chevrolet Corvette Z06, the supercharger on its 6.2-liter V8 more than making up for the discrepancy in displacement and cylinder count to produce 650 hp and just as much torque. But numbers don't tell the whole story, so watch the video clip to see which reaches the end of the quarter-mile first. News Source: To the Floor via YouTubeTip: James Chevrolet Dodge Videos drag race chevy corvette z06 quarter mile drag strip srt viper ta

More Corvette Stingray Factoids: Vanishing panel gaps and 26-mpg LT1

During January's Detroit Auto Show, we managed a longer than expected wandering tag-team interview with C7 Corvette chief engineering exec Tadge Juechter (pictured above), and LT1 engine boss Jordan Lee (pictured below). They are, quite honestly, two of the very nicest bigshot lads to ever walk the engineering corridors of an American manufacturer. Both are enthralled by what they're doing for a day job. So are we.
We've followed the pre-sale anticipation for the Chevrolet C7 Corvette Stingray like an Oreck vacuum yanking every speck of dirt from a well-trampled carpet. Everything is reportable and contains a grain of further knowledge about this dramatically important and cheered-for car, as it continues to be pressured into representing all that is superior about the American dream. The Corvette wears one heavy cloak.
So, most of what was talked about has been expertly reported already right here on Autoblog. But, looking through our notes again, both Jeuchter and Lee added facts to the buzzing mix.