2005 Chevrolet Suburban 1500 Z71 Sport Utility 4-door 5.3l 4x4 on 2040-cars

Auto blog

GM recalls 3.6 million vehicles for airbag-software problems

The Basics: General Motors is recalling 3.64 million vehicles across its lineup for an airbag-related issue. The recall covers the 2014-2015 Buick LaCrosse, Chevrolet SS, and Spark EV; 2014-2017 Chevrolet Corvette, Trax, Caprice PPV, Silverado 1500, Buick Encore, and GMC Sierra 1500; and 2015-2017 Chevrolet Tahoe, Suburban, Silverado HD, GMC Yukon, Yukon XL, Sierra HD, Cadillac Escalade, and Escalade ESV. The Problem: Affected vehicles have a sensing and diagnostic module that controls the airbags and seat-belt pretensioners. The software it uses has a defect that can prompt the module to run a diagnostic test under specific driving conditions, which will also deactivate the front airbags and pretensioners. This means that it would be possible for those safety systems to not activate in a crash, potentially leading to injury or death. Injuries/Deaths: General Motors began an investigation that led to the recall after a 2014 Silverado was involved in a crash in which the airbags did not deploy. No information was given as to injuries or deaths. The Fix: Owners can bring their vehicles to a local General Motors dealer where a software update will be installed to fix the issue. The fix will be free of charge. If you own one: General Motors will contact owners of affected cars, and owners can check whether their vehicles are affected by visiting entering their vehicle identification numbers at either the GM Owner Center website or the NHTSA website. Owners can then schedule a time to have the update installed. Related Video:

Chevy's 6.6-liter Duramax is pretty much all new

To say there's a heated battle in heavy-duty pickups is an understatement, with Chevrolet, Ford, and Ram constantly trading blows of increased torque, horsepower, and towing capacity. The latest salvo is the revised, more powerful turbo diesel 6.6-liter Duramax V8 in the 2017 Chevy Silverado. It has 910 pound-feet of torque, an increase of 145, putting it nearly level with the Ford Super Duty. Here's a closer look at where those gains come from. How exactly did Chevrolet add all that torque plus 48 horsepower? The automaker essentially took a fine-tooth comb to the entire engine. Chevy says it changed 90 percent of the V8, and the cumulative effect of those small changes adds up to big increases. As you might guess, the turbocharger is updated. The larger unit features electric actuation of the variable nozzle turbine (VNT), and what Chevy calls a double axle cartridge mechanism that separates the VNT moving parts from the housing. That helps with heat performance as well, with a claim that the exhaust side of the turbo can run continuously up to 1,436 degrees Fahrenheit. Helping that cause are six exhaust gaskets made of Inconel - an nickel alloy that contains chromium and iron – and upgraded stainless steel for the exhaust manifold. Despite having the same cast iron cylinder block, albeit with some minor enhancements, the engine has new cylinder heads, pistons, piston pins, connecting rods, and crankshaft, which have all been upgraded to handle 20 percent higher cylinder pressures. Alongside the increase in pressure, Chevrolet also increased the cylinder head's structure with a honeycomb design. The pattern features high-strength aluminum with dual layer water jackets that not only improve strength, but also optimize water flow for better cooling. For 2017, the cylinder head also benefits from integrated plenum that aids the engine in getting more air under heavy loads. The cylinder head isn't the only component to get a minor update, as the pistons have a larger diameter pin for improved oil flow. The same detailed improvements has been bestowed to the humble connecting rods (second in our hearts only to the inanimate carbon rod). The new design has the bolts oriented roughly 45-degrees to the rod instead of parallel. The angle split design, as it's called allows for easier passage through the cylinder.

1956 Corvette SR-2 factory racer profiled

The Chevrolet Corvette has earned its place as America's sports car, capable of taking on the best the world can throw at it. Much of that winning reputation was earned with victories on the track. Now, there was a chance to own an early piece of the nameplate's motorsport history in the form of a 1956 Corvette SR-2 racer, but some deep pockets were necessary to get it, with an estimate of $6.885 million. The story behind the SR-2 is fascinating. In 1956, famous General Motors designer Harley Earl's son was racing in a Ferrari. Obviously, that wasn't going to work given his father's position within the automaker, and Harley and Corvette engineer Zora Arkus-Duntov got to work on a faster racecar. Three were made. This one was reportedly the first, and for 1957 it also received a fuel-injected V8 making a claimed 331 horsepower and four-speed manual gearbox, according to "Corvette Mike," the owner and seller. The SR-2 went on display in Scottsdale, AZ appropriately timed to coincide with the big Barrett-Jackson auction there that wrapped up this weekend. The car wasn't part of that event; instead marque specialist Mike Vietro sold the racer as a private treaty sale. Company spokesperson Troy Worrell told Autoblog both the bids and identities of the bidders will remain undisclosed. The video above goes into even deeper detail about this rare, finned Vette or check out the car's full description for even more info.