1999 Gmc K1500 Suburban Slt Sport Utility 4-door 5.7l Leather 4wd *no Reserve* on 2040-cars

Auto blog

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck

GM trucks get hybrid versions, but you'll probably never see one

A few years ago, General Motors sold hybrid versions of its Chevy Silverado and GMC Sierra pickups. They weren't very good, using GM's old two-mode hybrid system that resulted in only negligible fuel economy gains. But GM's trying again, launching eAssist models of the 2016 Silverado and Sierra that are said to offer 2-mpg improvements in city, highway, and combined fuel economy ratings. Problem is, you probably won't be able to get one. Only 700 eAssist trucks will be made for the 2016 model year – 500 Silverados and 200 Sierras. When you consider that GM moved 824,683 examples of its light-duty pickups in 2015, this small run represents 0.08-percent of all Silverado/Sierra production, and GM says it "will monitor the market closely ... and adjust as appropriate moving forward." But that's not the only limitation. The eAssist trucks will only be sold through California dealers. For the Silverado, eAssist can only be optioned on the 1500 Crew Cab 1LT 2WD model, and for the Sierra, the fuel-saving technology is solely available on the 1500 SLT Crew Cab 2WD model with the SLT Premium Plus package. Granted, in terms of the Sierra, that means you get niceties like LED headlights and taillights, Apple CarPlay and Android Auto, Bose premium audio, heated seats and steering wheel, lane keep assist, and more. In the trucks, eAssist combines a small electric motor and 0.45-kWh battery pack with the pickups' 5.3-liter V8. GM estimates total output of 355 horsepower and 383 pound-feet of torque – no more horsepower than the non-eAssist trucks, but three more pound-feet of torque. GM says the eAssist trucks can tow up to 9,400 pounds, and the battery only adds 100 pounds to the trucks' weight. The electric motor provides 13 hp and 44 lb-ft of torque for a boost of acceleration off the line, or during passing. It also allows the engine to run in four-cylinder mode for longer periods of time. eAssist uses regenerative braking to help power onboard electrical systems, and adds start/stop to the powertrain. Finally, the so-equipped trucks have a six-percent improvement in aerodynamics, thanks to a soft tonneau cover and active grille shutters in the front fascia. Great news is, the eAssist option is relatively inexpensive, only costing $500. But good luck getting your hands on one.

Pure Vision Design TT Camaro has 1,400 reasons to want it

We've talked about Pure Vision Design before, a California-based company that made waves at last year's SEMA show with its Martini-liveried, Indy-car-powered Ford Mustang. That same car later starred in a Petrolicious video we showed you just a few weeks back. The company's latest creation is a menacing car it calls the Pure Vision Design TT Camaro. Based on a 1972 model, this car shares the Martini Mustang's clean styling and obsession with details.
Unlike the Mustang, which draws its power from a mid-60s Lotus-Ford Indycar engine, the "TT" in this Camaro's name implies something far more potent. The Nelson Racing Engines 427-cubic-inch V8 has been fitted with a pair of turbochargers, with a claimed output of 1,400 horsepower. That's almost 1,000 more than the Martini Mustang.
A six-speed Magnum transmission dispatches that power to the ground, while Pirelli PZero tires are tasked with (somehow) trying to grip the road. Baer brakes hide behind those HRE rims, while JRI coilovers and HyperTech springs bless the Camaro with some degree of competency in the bends.