2009 Chevrolet Silverado 3500 Hd Lt Extended Cab Pickup 4-door 6.6l 4x4 on 2040-cars

Auto blog

New GM subcompact SUV spied, could be a Chevy or GMC

GM's pair of subcompact crossovers have been trundling along for a while now. The Buick Encore was the first for Americans in the 2013 model year, and the Chevy Trax that was based on the Encore (an encore of the Encore, if you will) arrived for the 2015 model year. Each has undergone a mild update, but these spy photos could indicate their replacements are in the works. Or not. For starters, we can't be sure which GM brand this new SUV is destined for. Though the timing and its flowing lines could indicate Buick, the thick horizontal bars visible in the grille would indicate otherwise. The next Encore being at least related to this is at least a possibility. Making the case for GMC are those thick grille bars, the fact that it extends far below the lights, and may even rise above them, similar to the Acadia. And that rising beltline isn't that different from that of the Acadia. Arguing against the GMC idea is the Encore, which is almost always sold in GMC-Buick combo dealers. Much as the Acadia was made smaller to eliminate confusion and in-house competition with the Enclave, it's hard to see GM opting to resurrect such an issue at the bottom end of the SUV market. That means we're leaning toward this little SUV wearing a Chevy bowtie. The split grille with a large lower section and small upper section is the brand's current design language, as seen on the new Malibus and Cruzes. The shape is vaguely Equinox-like. And like Buick, Chevy also has a subcompact crossover ready for replacement: the Trax. Now, our photographer reports he's seen another subcompact testing that has Blazer design cues, but in this crossover-hungry market, we wouldn't be surprised if two similarly sized but differently styled Chevy crossovers make the grade. It's a strategy that's working pretty well for Jeep. We'll no doubt be seeing more of these disguised test vehicles milling about the country in the coming months, so perhaps we'll eventually get a better idea of what this is before more official information starts trickling out within one or two years. Related Video: Featured Gallery GM Subcompact Crossover spy shots View 10 Photos Image Credit: SpiedBilde Spy Photos Buick Chevrolet GM GMC Crossover SUV buick encore chevy trax

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck

GM cutting Chevy Sonic, Buick Verano production by more than 20%

General Motors' Orion Assembly plant in Michigan is seeing even more production cuts this year to further reduce inventories of the Chevrolet Sonic and Buick Verano. These latest adjustments mean layoffs for about 100 workers in phases starting in July. "GM Orion Assembly will adjust plant production capacity to better align with market demand," the company said in a statement announcing the change. Through May, sales of the Sonic are down 28.5 percent to 29,082 vehicles, and the Verano is off 15.6 percent, with 15,279 sold this year. According to unnamed plant insiders speaking to Automotive News, the assembly rate is slowing at Orion Assembly from the current 33 cars an hour down to 26 an hour, a 21-percent reduction. GM is also reportedly going to keep the plant idle for three weeks during the normal summer shutdown, rather than the usual two. Earlier in the year, the factory was idled for two weeks due to excess supply of the Sonic and Verano. In March, it was closed again for several days for the same reason. The Orion Assembly plant is the future home to the line for the Chevy Bolt EV. GM Statement: GM Orion Assembly will adjust plant production capacity to better align with market demand. A phased layoff of approximately 100 employees will begin in July 2015 and conclude by year-end. Related Video: News Source: Automotive News - sub. req.Image Credit: Bill Pugliano / Getty Images Plants/Manufacturing Buick Chevrolet GM Hatchback Sedan buick verano orion assembly