2006 Chevrolet Silverado 3500 Work on 2040-cars

Auto blog

Driving Granatelli's turbine-powered 1978 Chevy Corvette [w/video]

With its curvy snout and feminine haunches, the third-gen Chevrolet Corvette looks like a dreamy – if dated – exemplar of Sports Car Fantasy 101 when viewed through modern eyes. This particular specimen circa '78, clad in silver and black paint with red pinstripes, appears to be a well-preserved example from the era. Apart from its low-profile Pirellis, slightly raised and slotted hood, spacious stance and a certain hand-painted descriptor alongside its crossed flag logos, you'd never guess there's a Space-Age propulsion unit powering this Coke bottle-bodied ride. Climb inside, and you're presented with aircraft gauges and big, colorful square buttons in the center panel. It takes a push of the "Ignitor" button, a tap of the starter button, and a slide of a T-handle for this nearly 40-year-old sports car to start sounding like Gulfstream G650 ready for takeoff. Yep, you're sitting in an 880-horsepower, turbine-powered Corvette, the only one of its kind in the world. Welcome to the whoosh. What The...? Built by Vince Granatelli, son of Indy 500 guru Andy Granatelli, this curious Corvette came into being by cramming a Pratt & Whitney ST6N-74 gas turbine engine into the donor car's lengthy front end. The same type of Jet A-burning mill powered Granatelli Senior's STP-sponsored racecar at the 1967 Indianapolis 500, where it famously led most of the 198 of 200 laps until a $6 transmission bearing failed, knocking it out of the race. The idea of turbine power usurping internal combustion was so threatening that Indy's governing body restricted turbine performance into obsolescence thereafter. A turbine-powered Corvette sounds excessive because it is. But there are also things about this 880-horsepower, 1,161-pound-feet monster that might surprise you. While it smacks of futurist exoticism and cost a then-dizzying $37,000 in 1967, the Canadian-built powerplant uses 80 percent fewer parts than an internal combustion V8 and will run on virtually anything combustible – whiskey, diesel, even Chanel No. 5. Though it's triple the length of a V8, the Pratt & Whitney beast weighs only 285 pounds. It's also one hell of a robust workhorse, typically serving as an auxiliary power unit for commercial aircraft or a generator in oil fields, where it can run for tens of thousands of consecutive hours before needing an overhaul. To adapt the Chevrolet for jet duty, the nose section was gutted and a sub-frame was built to compensate for the loosey-goosey front end.

2021 GMC Canyon trims overhauled, SL and SLT disappear

Until this year, the GMC Canyon has offered six trims in two drivetrains: SL, a base model simply called Canyon, SLE, All Terrain, SLT, and Denali, with all but the SL available in either 2WD or 4WD. GM Authority credits "dealer sources" for news that the 2021 Canyon has had its trim steps overhauled. According to the chart in the report, the SL and SLT are no more, the base Canyon gets replaced by a trim called Elevation Standard, and SLE turns into Elevation. We already know that All Terrain has given way to AT4, while Denali remains in the top spot. Trim content doesn't change with the names, but there's no equivalent for the SLT trim in terms of spec. The GMC site lists the 2020 SLE and SLT on the same page, and a shopper must burrow into the spec comparison page to figure out the differences. The SLT only comes with the 3.6-liter V6 and eight-speed transmission, and makes features like remote start, climate control, heated mirrors, heated seats, hitch guidance, and a spare tire standard equipment. It also chromes the exterior door handles, and offers a Cocoa/Dune leather interior that can't be had on the SLE. It's possible the SLT's $4,700 premium over the SLE led more buyers to start with the SLE and add the engine and options they wanted.   We have a number of questions that we'll need to wait for GMC's official announcement to answer. The 2020 Canyon offers an Elevation Edition package for $650 that adds a black grille with body-colored surround, and 18-inch Satin Graphite wheels in all-terrain rubber. There's also a California Elevation Special Edition for $1,195 with all-weather floor liners, assist steps, and mud flaps. They could be optioned on the SLE but not the SLT. With the addition of two Elevation trims, we'll find out if the packages get renamed or go away. Separately, CarBuzz spotted a 2021 GM Fleet Order Guide that mentions a leveling kit option, LPO Code SQS, for the Canyon and the Chevrolet Colorado. We noted the inclusion of a leveling kit in the coming Canyon AT4 Off-Road Performance Package. According to the order guide, the option can be ordered only for the Canyon AT4 trim, but it's not clear if that's an a la carte choice or if buyers must order the Off-Road Performance Package. On the Chevy, the rake-removal equipment can be had with the Colorado 4x2 Z71 or the 4x4 Work Truck, LT, and Z71. Related Video:

GM announces $7 billion Michigan factory investment, most going to EVs

GM announced a $7 billion investment in Michigan manufacturing, much of which is earmarked for EV production. Four sites are included, but the key elements are a new battery cell plant in Lansing and the conversion of GM's existing Orion Township facility to expand production of the forthcoming Chevrolet Silverado EV and its GMC Sierra sibling.  GM says it is the largest investment announcement in company history and that it will create 4,000 new jobs. It also says 1,000 jobs will be retained. "We are building on the positive consumer response and reservations for our recent EV launches and debuts, including the GMC Hummer EV, Cadillac Lyriq, Chevrolet Equinox EV and Chevrolet Silverado EV," said GM CEO Mary Barra.  GM says the Orion expansion and new battery plant will support an increase in full-size electric truck production capacity to 600,000 units. This is in addition to the Factory ZERO facility in Detroit that will also be constructing the electric Silverado and Sierra.  The Orion Township factory current builds the Chevrolet Bolt EV and EUV, and will continue to do so during the plant's conversion. GM did not indicate what will happen with the Bolts once that conversion is complete or whether all will continue to be built at Orion. They do not use the Ultium vehicle architecture. GM will build other EV models at three other factories that are under construction or being converted. They are located in Spring Hill, Tennessee, Ingersoll, Ontario, and Ramos Arizpe, Mexico. GM says that it will have the ability to produce 1 million electric vehicles by 2025. The Ultium Cells Lansing facility is a $2.6 billion joint investment by GM and LG Energy Solution. GM says it alone will create 1,700 jobs once fully operational by late 2024. It will join two other GM Ultium Cells battery factories currently under construction in the United States, one in Ohio and the other in Tennessee.  Not all of the $7 billion investment will be for EVs. It also announced $510 million of the total will go toward upgrading the Lansing Delta Township Assembly to produce the next-generation Chevrolet Traverse and Buick Enclave. Money will also go to upgrading Lansing Grand River Assembly.