2004 Chevy 3500 Diesel 4x4 Dually Lt Heated Leather Bose on 2040-cars

Auto blog

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck

Chevy Colorado, GMC Canyon get updated tachometers due to graphical error

After James Bearing bought a Chevrolet Colorado, he noticed a discrepancy between the truck's spec sheet and the truck's tachometer: Chevrolet said 3.6-liter V6 in the little pickup produces 305 horsepower at 6,800 rpm, but the the tachometer indicates a redline at 6,500 rpm. So either he wasn't making as much power as he was promised, or the tachometer display was incorrect. Bearing said he asked Chevy about it but got no response. Until now. A General Motors spokesman said the rev limiter is indeed set for 6,800 rpm, but the tach graphics "are slightly off" in the Colorado and the GMC Canyon, and submitted an SAE horsepower certification to back him up. If you're wondering how such a thing got past quality control... well, let's just say you're not alone. GM is going to fix "the graphics on future trucks," which makes it sound like Bearing will just have to learn to live with the indicated redline he's got. He could always pretend he's driving a sleeper, with four more ponies waiting to be unlocked in the danger zone for those who dare. Related Video: Featured Gallery 2015 Chevrolet Colorado: First Drive View 38 Photos Related Gallery 2015 GMC Canyon: Quick Spin View 27 Photos News Source: Auto Guide Auto News Chevrolet GM GMC Truck gmc canyon

First 2015 Chevy Corvette Z06 engine blows up at just 891 miles

You've waited and watched and waited some more for the arrival of your 650-horsepower, $78,000 Chevrolet Corvette Z06. Finally, that joyous day arrives and you eagerly, but gingerly, begin to break-in the 6.2-liter supercharged V8 monster under your hood. Then 900-odd miles after delivery, your excitement grinds, quite literally, to a halt. That's what the owner of one 2015 Z06 claimed happened to him when a simple break-in drive resulted in a lunched engine. The owner, known as Lawdogg149 on Corvette Forum, says he was out breaking-in his car ahead of a January track event when it happened. "While making a pull from 35 miles per hour, I accelerated and shifted short of redline, and boom - the car began knocking. I pulled over and popped the hood. I could hear a loud knock coming from the No. 6 cylinder area along with a serious, grinding, metal-on-metal sound coming from the supercharger area," Lawdogg wrote. A subsequent trip to the dealer confirmed his concerns, with the service facility telling Lawdogg that the No. 6 valvetrain had failed. The dealer couldn't research the issue further, though, as General Motors requested the engine be returned for a more thorough evaluation. The good news for the Z06's unlucky owner, at least, is that GM will be covering the engine replacement under warranty, an expense that Corvette Forum estimates is a nearly $24,000 procedure. At this point, the two leading theories behind the engine's detonation involve a manufacturing defect – which could be why GM is so keen to tear the blown powerplant down – or a mistake on the part of Lawdogg. As Motor Authority points out, such an error could be something as simple as the Z06's owner accidentally shifting to first rather than third during his 35-mph pull. If, however, there's a deeper manufacturing problem with the Z06's engine, this might not be the only case we end up hearing about.