2008 Chevrolet Silverado 2500hd Lt 4wd Tintedwindows Towpkg Dualzoneclimate on 2040-cars

Auto blog

GM recalls 8,500 Chevrolet Malibu models for rear suspension glitch

According to a letter from General Motors to the National Highway Traffic Safety Administration, flaws in the build process of the 2013 Chevrolet Malibu have led to the recall of 8,519 cars. Units built between December 6, 2011 and January 15, 2013 may have been assembled with rear suspension cradles that had insufficient torque applied to certain bolts. That out-of-spec assembly could lead to issues ranging from slight noises to a loss of vehicle control.
The problem was first noticed in December of last year by a GM test fleet driver and eventually tracked back to the improperly torqued bolts on the suspension cradle assembled through July 2012 by a supplier located not too far from the Malibu's Detroit/Hamtramck Assembly Plant. Since an official NHTSA recall notice has not been issued yet, it isn't clear whether or not Detroit-built Malibus were the only ones affected (the 2013 Malibu is also built at GM's Fairfax Assembly Plant in Kansas City, Kansas). Dealers will fix the problem by inspecting vehicles for proper torque specs, retightening if not within specs and, in some cases, perform a rear-wheel alignment.

GM recalls 3,300 pickups and SUVs for new ignition-switch issue [UPDATE]

UPDATE: A statement from GM about the recall has been added below. The exact total of vehicles affected is 3,296, including 3,073 of them in the US. General Motors isn't letting an ignition-switch problem grow into a massive scandal again. The automaker is recalling about 3,300 North American trucks and SUVs. They are: the 2014 Chevrolet Silverado and GMC Sierra and the 2015 Chevy Suburban and Chevy Tahoe, as well as 2015 model heavy-duty pickups, the Detroit News reports, citing an Associated Press story. The issue appears to have been caught fairly quickly. In this case, the keys can get stuck in the "start" position and then slip to "accessory" if bumped. This is because the ignition lock gears have an outer diameter that's larger than the specifications allow. When that happens the engine shuts off, and the driver loses assistance to the steering and brakes. The airbags might also be affected. The vehicles get a new ignition-lock housing to fix the problem. According to the Detroit News, an employee who experienced the problem with the switch discovered the issue, and this person then let officials at the automaker know as part of the Speak Up for Safety program. A total of five reports of the fault were discovered. However, there are no cases of injuries or crashes. The claims to the automaker's resolution program eventually tallied that GM's previous ignition switch problem included 124 deaths and 275 injuries. The company also had to recall millions of vehicles and pay significant fines to the US government. GM Statement General Motors is recalling 3,073 full-size trucks from the 2014 and 2015 model years in the U.S. Some of these vehicles may have an ignition lock actuator gear with an outer diameter that exceeds specifications, which may make turning the ignition key difficult. The ignition key could get stuck in the "start" position. This may be more likely at higher interior ambient temperatures. If the vehicle is driven with the key stuck in the "start" position, and the vehicle experiences a significant jarring event or the vehicle's interior temperature cools, the ignition lock cylinder could move out of the "start" position, rotate past the "run" position, and move into the "accessory" position, leading to loss of power steering assist, power brakes and potentially air bag deployment in certain crashes. Dealers will replace the ignition lock housing.

Surprise! GM putting aluminum in next-gen pickups

Last month, General Motors launched a series of ads touting the benefits of steel over aluminum – specifically, with regard to the Chevy Silverado versus the Ford F-150. (Kind of. We're not sure what a grizzly bear has to do with anything.) We took issue with the ads, with editor in chief Mike Austin saying they "reek of insecurity, and distract from the Silverado's strengths that could be used for positive advertising." But what bothers us more, is that yet another report surfaced claiming anti-aluminum GM will indeed use the weight-saving material in its next-generation fullsize trucks. On Tuesday, GM announced a $877-million investment for its truck plant in Flint, MI. But Reuters says that huge overhaul is because the trucks will use "substantially different equipment than the tools GM uses today." The report specifically states, "People familiar with the company's plans say GM's next-generation pickups and SUVs will make use of various materials, including aluminum and lightweight steel, to shed weight and gain fuel efficiency to meet tougher federal standards." The Silverado already uses a few aluminum components in the engine and hood, and if more widespread use will help GM build its best fullsize trucks ever, then that's great. Honestly, we have no reason to doubt that aluminum will be used in the next Silverado and GMC Sierra. We just hope GM remembers that nothing is ever truly deleted from the bowels of the Internet when it launches the subsequent "look how great aluminum is!" campaign. Related Video: News Source: Reuters Green Plants/Manufacturing Chevrolet GM GMC Truck aluminum steel