2013 Chevrolet Silverado 1500 2wd Crew Cab 143.5" Lt on 2040-cars

Auto blog

Fullsize GM SUVs have a problem that's making owners sick

Some fullsize SUV owners are getting sick, thanks to a buffeting and vibration problem in 2015 model year examples of the Chevy Tahoe and Suburban, Cadillac Escalade, and GMC Yukon. According to owners' complaints to the National Highway Traffic Safety Administration, the issue can vary from an annoying vibration inside the cabin to an experience so severe that it leads to dizziness and headaches. General Motors is aware of the complaints, but the fix isn't so simple. According to spokesperson Tom Wilkinson to Autoblog, the company "has been tracking this issue for a while." The problem has a fairly low incidence rate, but when it does occur the issue can be "uncomfortable and annoying for owners." There's no precise cause for the issue, Wilkinson claims, and in some cases, simply balancing the tires or changing the door seals can make it go away. However, not all of the fixes are so simple. AutoGuide dug deep into the problem and discovered a GM preliminary information bulletin that advised dealers to remove the headliner and to check the roof's bonds to the bows that go across the vehicle. However, that document included a note that the solution might not entirely eliminate things. According to AutoGuide, adding Dynamat insulation to the roof sometimes helped the problem. A GM spokesperson also told AutoGuide the company fixed the problem at the end of the 2015 model year, and didn't go into any more detail. This roof issue seems linked to some of the worst droning in these SUVs. According to one complaint from a 2015 Suburban owner to NHTSA: "Roof will not remain attached to the roof bows. This causes the buffeting similar to a window being down when all are up. The results span from annoying to painful." A 2015 Yukon owner claims to have another alleged cause for the problem in a NHTSA complaint from February 2015. This person brought their SUV to the dealer seven times over the course of four weeks for vibrations. The dealer replaced the driveshaft, suspension components, and more, but nothing worked. According to an engineer to the service adviser: "In an effort to prevent roll overs, they designed the frame and body mounts too stiff. There are 40 engineers working on issues, they have no solutions that work across the board." Wilkinson told Autoblog that GM is working with customers on an individual basis to rectify things. Since these are newer vehicles, dealers should also fix the problem under warranty.

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck

1983 Motorweek showdown pits Porsche 928S vs. Chevy Camaro Z28

Last month, Motor Trend threw the Camaro Z/28 and Porsche 911 GT3 into the bear pit and let them fight it out. Way back in 1983, MotorWeek had the same idea, comparing the Camaro Z/28 to the Porsche 928S. At the time, the Camaro was America's best selling sports coupe, the 928S was Porsche's top-of-the-line model that also had the highest top speed of any car sold here. And the price differential was even more stark then: $13,600 for the Camaro, $45,000 for the Porsche. That put the Z/28's cast-iron, 5.0-liter V8 with 190 horsepower and 240 pound-feet of torque against the all-aluminum 4.7-liter V8 with 234 hp and 263 lb-ft in the 928S. Even with that and the Camaro being 14 inches longer than the Porsche, the American was a surprising 40 pounds lighter than the German. The show took them to Summit Point Raceway in West Virginia to see how close a relative performance bargain could hang with a the German GT. Both had five-speed manual transmissions, but the high-speed corners and tight sections of Summit Point would test other handling variables, including the "bone-rattling" Camaro's solid rear axle and disc and drum brake setup vis-a-vis the four-wheel disc brakes and independent suspension on the "firm-but-smooth" Porsche. Paradoxically, the larger disparity 22 years ago resulted in a closer result. Check out the video to see how the Summit was won. News Source: MotorWeek via YouTube Chevrolet Porsche Coupe Luxury Performance Classics Videos chevy camaro z28 porsche 928 retro review