2004 Gray Cloth Trailer Hitch V8 Vortec Used Preowned 157k Miles on 2040-cars

Auto blog

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck

Final C6 Corvette built in Bowling Green

With all of the attention given to the 2014 Chevrolet Corvette Stingray lately, you could be forgiven for thinking that it's already well along in production, yet tooling up for the new C7 has only just begun. In fact, production of the outgoing C6 generation in Bowling Green, Kentucky just halted on Thursday.
As the C6 has aged, production numbers have predictably ebbed along with demand, but this year, the addition of the 427 and 60th anniversary models resulted in an uptick in vehicles built - this, despite a model year shortened by around 25 percent to accomodate the new model changeover. The final C6 Corvette ever, No. 13,466 built this year, was a white 427 Convertible destined for the General Motors Heritage Center museum. The car's 7.0-liter V8 heart was assembled by Corvette chief engineer Tadge Juechter himself.
In total, Bowling Green pushed out 215,100 C6 Corvettes over nine years. If you're still a C6 fan at heart and are hoping to get a good deal on a phase-out model, step lively - Chevrolet reportedly had about 6,100 unsold units, which Autoweek suggests is good for around five and a half months of supply at the model's current sales rates. Given that demand will likely slacken even further as the C7 draws closer, that should be a big enough stockpile to keep dealers satisfied until 2014 Stingrays begin showing up on their forecourts in December.

GM recalling 521,817 cars in two campaigns

General Motors is issuing two, separate recalls covering a total of 521,817 vehicles worldwide. The larger campaign covers 468,887 units of the 2011-2012 Chevrolet Malibu. Specifically, 437,045 of these are in the US, and the rest are outside the country. In these sedans, a steel cable that connects the seat belt to the vehicle can fatigue and separate. GM knows of 36 claims about the problem but only one minor injury. According to The Detroit News, this happened when a taxi driver hit his head. To fix things, dealers will replace the "outboard lap mounting bracket," which will move the tensioner rearward. They'll also inspect and if necessary replace the steel cable and lap pretensioner. In the second campaign, 52,930 examples the 2015 Chevy Colorado and 2015 GMC Canyon have seat frame attachment hooks that were installed incorrectly during assembly. GM hasn't received any reports of crashes, injuries, or fatalities about this problem. Dealers will inspect the affected trucks and repair as necessary. GM spokesperson Alan Adler told Autoblog that he didn't yet have a specific date when affected owners would receive official mailings about either of these recalls. GM Statement General Motors is recalling 48,309 2015 model year Chevrolet Colorado and GMC Canyon midsize pickup trucks in the U.S. because certain seat frame attachment hooks were not properly attached to the vehicle body during assembly. Dealers will inspect the potentially affected seats for proper installation and repair if necessary. GM knows of no crashes, injuries or fatalities related to this condition. The total vehicle population of the recall is 52,930 including 4,620 vehicles sold in Canada. General Motors is recalling 437,045, 2011-2012 model year Chevrolet Malibus in the U.S. because the flexible steel cable that connects the safety belt to the vehicle can fatigue and separate over time as a result of occupant movement in the seat. Dealers will replace the outboard lap mounting bracket to relocate the tensioner slightly rearward. Dealers will inspect the cable and, if necessary, replace the lap pretensioner. GM knows of 36 claims, no crashes or fatalities and one minor injury reportedly related to the condition. The total vehicle population of the recall is 468,887 including Canada, Mexico and exports.