Pick Up Truck, Black, Chevy S10, 1999, Regular Bed, New Headliner, on 2040-cars

Auto blog

Chevy Bolt-based prototype may be a Buick EV for China

Late last spring, we got a look at a GM prototype that was clearly based on the Chevy Bolt EV, but with updated styling. It seemed like it could be a more crossover-styled Bolt, given the recently trademarked name of EUV. Now we get another look at the prototype, but the bodywork seems less suggestive of a Chevy, and more of a Buick. This vehicle definitely still appears to be based on the Bolt, rather than on another small GM platform. In the photos of it next to the current model, the size, wheelbase and profile are extremely similar. There are differences, though. The nose isn't as sloped or as rounded, and the rear window kicks up a little earlier. The biggest changes are in the front and rear fascias, and it's here that we see hints of Buick. There are prominent air inlets on each side of the front bumper that give the car a more aggressive look. The headlights still have a fairly rounded, organic look, but with little extensions like fangs underneath. The styled running-light section, rounded shape and the smoked lenses seem very Buick-like. The grille features a large badge that doesn't fit the shape of a bow-tie, and is more that of a round logo like Buick's. Around at the back, the full-width taillights stand out, and in the middle there is obviously a round badge, again like a Buick. The wide taillights would also be a natural evolution of Buick's current light design language that uses somewhat wide and thin lights. The rear bumper has been redesigned with new lower taillights. Now that we've established that this seems very much like a Buick, we don't think we'll see this particular version offered here with the badge. This is more likely a Buick version of the Bolt for the Chinese market, where the brand is associated with luxury and has been the spearhead for GM's electric and hybrid models. In fact, the Chevy Volt hybrid was sold there as the Buick Velite 5, which was part of a family of a electrified Velite models. This would probably also carry a Velite badge as well. While we might not see this specific Buick variant, we probably will see it offered as a Chevy in some form. With its more aggressive, crossover shape, it could be the rumored EUV model. Or it could be just a refresh of the current Bolt, since the model has been largely unchanged since its introduction for the 2017 model year. And extrapolating from this prototype, we can see how the headlights could be tweaked to tie into those air scoops as on the Suburban and Silverado.

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck

Autoblog Podcast #380

Episode #380 of the Autoblog podcast is here, and this week, Dan Roth, Chris Paukert and Seyth Miersma talk about the Fiat-Chrysler five-year plan, the seeming demise of the Nissan Cube, and proposed legislation to require speed limiters with a 68-mph maximum on America's tractor trailers. We start with what's in the garage and finish up with some of your questions, and for those of you who hung with us live on our UStream channel, thanks for taking the time. Check out the new rundown below with times for topics, and you can follow along down below with our Q&A. Thanks for listening! Autoblog Podcast #380: Topics: Fiat-Chrysler five-year plan Nissan Cube on the way out? Big rig speed limiters coming? In the Autoblog Garage: 2015 Mercedes-Benz S63 AMG 2014 Chevrolet Sonic RS Sedan 2014 Honda Odyssey Touring Elite Hosts: Dan Roth, Chris Paukert, Seyth Miersma Runtime: 01:44:17 Rundown: Intro and Garage - 00:00 Fiat Chrysler Plan - 29:40 Nissan Cube - 01:07:33 Semi Speed Limiters - 01:17:33 Q&A - 01:27:35 Get the podcast: [UStream] Listen live on Mondays at 10 PM Eastern at UStream [iTunes] Subscribe to the Autoblog Podcast in iTunes [RSS] Add the Autoblog Podcast feed to your RSS aggregator [MP3] Download the MP3 directly Feedback: Email: Podcast at Autoblog dot com Review the show in iTunes Auto News Earnings/Financials Plants/Manufacturing Podcasts Rumormill Chevrolet Chrysler Dodge Fiat Jeep Nissan nissan cube speed limiters