2003 Chevy S10 Ext Cab 2.2 Airbag Suspension on 2040-cars

Auto blog

Chevy Sail 3 lands in China

Shanghai General Motors took 32 cars to this year's Guangzhou Motor Show, with its Chevrolet Sail 3 leading the way. After putting almost 1.4 million of them into Chinese hands, the third generation of the Bowtie's entry-level sedan wants to "take the nameplate and the segment to a new level." Its new architecture sporting a 1.4-inch longer wheelbase supports a growth spurt of two inches in length and 1.8 inches in width. The exterior also gets "eagle eye-shaped" headlights and "dual-c-element taillights." Under the hood will be either a 1.5-liter DVVT or a 1.3-liter VVT, each of them more powerful and more frugal than previous offerings. Both can be paired with a manual or an automatic transmission, and qualify for listing in China's National Energy-Saving and Eco-Friendly Vehicle Catalogue, as well as a 3,000 renminbi rebate ($490 US). You can read more about it in the press release below, and get more info on the Chevrolet Camaro RS Limited Edition, Corvette Stingray Coupe, Buick Regal GS and Excelle XT also introduced at the show. Chevrolet, Buick and Cadillac Take Center Stage at Guangzhou Auto Show - New Chevrolet Sail 3, Camaro RS Limited Edition and Corvette Stingray Coupe make China debut - Buick showcases customized Regal GS and Excelle XT - Shanghai GM announces new telematics strategy featured in upcoming Cadillac product GUANGZHOU, 2014-11-20 – Shanghai GM is displaying 32 vehicles from the Chevrolet, Buick and Cadillac brands at the 12th Guangzhou International Auto Show, which begins today and runs through November 29 in Guangzhou. Among the products that are making their China debut are the third-generation Chevrolet Sail 3, Chevrolet Camaro RS Limited Edition and Chevrolet Corvette Stingray Coupe. In addition, Buick is showcasing a customized Regal GS and Excelle XT, and Shanghai GM is announcing its new telematics strategy that will be featured in an upcoming Cadillac product next year. Chevrolet Sail 3 Entry-Level Family Car Since its introduction 15 years ago, the Sail has been a driving force in the entry-level family car segment. Nearly 1.4 million Sails have been sold across China. The third-generation Chevrolet Sail, named the Sail 3, will take the nameplate and the segment to a new level when it goes on sale nationwide by the end of this year. Built on Shanghai GM's new-generation small car architecture, the Sail 3 has adopted Chevrolet's new design language. It has a sculpted yet slim exterior with a youthful, dynamic feel.

Camaro spy shots show subtly different grille, front fascia

It looks like there some changes in store for the Chevrolet Camaro - the only thing is that we just don't know what Chevy has up its sleeve. Looking at these spy shots, we'd initially be inclined to think that there is just a minor facelift or a new special edition, but upon closer inspection, there are a few oddities about this car that definitely have us intrigued.
The most obvious difference on this prototype is the slightly restyled front fascia with a smaller lower air inlet and the two-bar grille. Then we get to some of the car's mysterious details. For starters, this fascia has the SS vent above the grille, but it looks to be blocked off. Granted this could just be a one-off piece used for testing. What really piqued our interest was at the rear of the car where it has quad exhaust outlets that are used on the ZL1. Could this be the LS7-powered Camaro that we reported on back in December?
At this point, your guess is as good as ours as to what we're looking at here, so let us know in the comments what you think this could be.

Experimental mid-engine XP-819 Corvette going up for auction

It seems to be commonplace that when a new Corvette is in development, rumors swirl about a possible mid-engine layout. As is the case of Chevy's most recent C7 Corvette, these rumors never pan out.
In any case, the idea for a 'Vette with an engine mounted behind the driver can probably all be traced back to a single car, the 1964 XP-819 prototype. Built as an "engineering exercise" back in 1964, the prototype was designed with a rear-mounted engine. History tells us that the idea of a rear-engine Corvette fizzled, and the XP-819 was eventually cut up into pieces and stored at a shop in Daytona Beach, FL.
After sitting for untold years, a restoration project started on the car, and while it isn't yet fully completed, the current owner of the car, Mid America Motorworks, will have the car on display at the 2013 Amelia Island Concours d'Elegance as a "driveable chassis" with hopes of having a fully completed car ready to bring to next year's show.