1993 Chevrolet S10 Blazer Tahoe Lt Sport Utility 4-door 4.3l on 2040-cars

Auto blog

Fewer than 1 in 3 Chevy dealers earn right to initially sell C7 Corvette

Looking to make the launch of the 2014 Corvette Stingray as efficient as possible, Chevrolet will be limiting the numbers of its dealers that can sell the all-new coupe and convertible. According to Automotive News, sales of the C7 Corvette will initially be limited to less than a third of Chevy's total dealership network when the 'Vette goes on sale this summer.
Only 900 dealers out of more than 3,000 locations nationwide will be allowed to sell the new Corvette at first, and the reason for this is so that there are no shortages at dealers that can actually get the cars sold. The article says that the 900 dealerships chosen represented 80 percent of total Corvette sales in 2012.
Some of the requirements dealers had to make to get initial allocation of Stingray sales include having sold at least four Corvettes in 2012 and having a Corvette Stingray specialist who will be required to have gone through a training session costing more than $2,000 per attendee. Once demand for the 2014 Corvette Stingray begins to subside - approximately six to nine months after it goes on sale - then allocation could open up to more dealers, but the report indicates this could happen following the 2014 model year.

2014 Chevrolet Silverado tows in new configurator, microsite

Judging by your continued enthusiastic response to configurator notices, dear reader, you enjoy speccing out new cars as much as we do. Better still, there tends to be even more ways to personalize, configure and bloat theoretical MSRPs on full-size trucks as there are with more ordinary passenger cars. In addition to trim level, engine and transmission choices, truck buyers usually have to specify items like cab configuration, bed length, number of driven axles, tow packages, gear ratios and all sorts of bits and bobs.
That's why we're pleased to see the DIY specification utility for the 2014 Chevrolet Silverado come alive so soon after this week's Detroit Auto Show debut. While the configurator lacks pricing (General Motors hasn't announced numbers yet) and full options, you can still spec out your half-ton rig, and even print it out or email it to your friends. Beyond the configurator, the new model-specific site is pretty cool, too, with various videos and closer looks at the truck's new features.
The new Chevrolet pickup range won't be on dealer lots until sometime this summer, so whether you're a building contractor, an avid sportsman or just a guy or gal that loves full-size trucks, you might want to check out the link below to keep your appetite whetted. If you're more of a Sierra fan, well, it looks like you're going to have to wait a while - GMC hasn't updated its site yet.

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck