1959 Chevy Apache Long Bed Customized V8 on 2040-cars

Auto blog

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck

How GM engineers are using diaper 'snow' to keep you warm

Testing how snow affects General Motors' vehicles isn't really a problem right now for the company's engineers, but in the dog days of summer the process isn't exactly easy. The only real option is for them to book time at the automaker's climatic wind tunnel. However, a flash of brilliance from an engineer allows snow to be simulated regardless of the temperature outside, and the discovery is all because of his daughter's wet diaper. The realization came to GM Thermal Systems engineer Nicholas Jahn while he was swimming with his daughter and noticed how her diaper ballooned in size in the water. He found out the substance that makes this possible is called sodium polyacrylate. When the material gets wet it grows and forms fluffy flakes that are a close imitation of snow. Best of all, the stuff can be prepared easily any time of the year, and it's reusable. The engineering team uses the material to test the effectiveness of the heating systems of GM's vehicles. They spread the sodium polyacrylate over the inlets at the base of the windshield to obstruct the airflow and then crank the heater. After some time, they can see how much is being sucked into the system and design more efficient systems in the future. See how the process works in the video above and read about the diaper discovery in GM's press release below. Diapers Change Chevy Cruze Winter Warm-up Time GM validation engineer uses diaper material "snow" to reduce frigid drives 2015-01-06 DETROIT – An item commonly found on an infant's changing table is helping General Motors' engineers simulate snow year round, ensuring heating systems in cars like the 2015 Chevrolet Cruze can quickly and efficiently warm its interior. Packed snow can prevent air from entering the inlet panel at the bottom of the windshield, obstructing the flow of air into the heating system and reducing the amount of air it can push out. This can lead to less efficient warming of the car's interior and windshield defrosting. "The last thing anyone wants to do when it's freezing cold out is scrape their windshield," said Nicholas Jahn, GM Vehicle Thermal Systems engineer. "The testing we perform on the Chevrolet Cruze with the diaper material allows us to maximize the car's heating capabilities." Ironically, Jahn stumbled upon his diaper-based testing method in the middle of summer. During a swim with his daughter, he noticed her diaper multiplied in size when it came into contact with water.

Watch the National Corvette Museum sinkhole being filled in by R/C cars

Okay, so not exactly cars, but Bobcats - but still quite cool. You might remember that the National Corvette Museum had that little divot that needed to be filled in. Turns out the construction firm of Scott, Murphy & Daniel doing the work is using two remote-controlled Bobcats to fill the sinkhole with "manufactured sand," which in this case is crushed limestone. It appears that the Bobcat company has offered remote operation since at least 2007 via a wireless transmitter that works up to 1,500 feet away. So yes, that means two SMD employees stand on the edge of the pit and flick joystick levers for hours at a time, one in charge of a Bobcat with a roller-compactor attachment, the other in charge of a Bobcat with a bucket. And that, to us, is a pretty good way to earn the daily bread. Check out the video above for the latest sinkhole update. News Source: National Corvette Museum via YouTube Auto News Weird Car News Chevrolet GM Videos rc car remote control National Corvette Museum bobcat ncm