1939 Chevrolet Pickup 1/2 Ton Street Rod Coke Diner on 2040-cars

Auto blog

Sinkhole Opens Up In National Corvette Museum, Swallows Eight Cars

More cars are being moved inside the National Corvette Museum in Bowling Green, Ky. to avoid falling down the same sinkhole that swallowed eight classic sports cars early this morning, Autoblog reported. Museum officials said the hole was discovered when motion sensors activated around 5:45 a.m. The rescue mission can be viewed on the museum's live feed cameras, which weren't working after the sinkhole emerged. A 1993 ZR-1 Spyder and a 2009 ZR1 "Blue Devil," both on loan from General Motors, were among the cars that fell into the sinkhole. The museum owned the other affected Corvettes, which included a 1963 Corvette, a 1984 PPG Pace Car and the 1 millionth Corvette ever produced. The state of the cars at the bottom of the hole isn't known, but trial lawyer and sinkhole expert Ted Corless said the cars may be a total loss for the museum and GM. "Most states, including Kentucky, exclude damage caused by sinkhole activity," he said. "There will be, in all likelihood, a claim made, but a lot of policies would specifically exclude these kinds of damages." Corless has 15 years experience dealing with sinkholes. He said that typically neither the building, nor the cars themselves are protected under their insurance policies. "I would have to say, more likely then not, they're going to have an uninsured loss measured in the hundreds of thousands of dollars." The museum is closed Wednesday while a structural engineer assesses the damage. Related Gallery 2014 Chevrolet Corvette Stingray Test Drive View 9 Photos Related Gallery 2014 Chevrolet Corvette Stingray Test Drive View 9 Photos Weird Car News Chevrolet GM corvette

GM recalls 3,300 pickups and SUVs for new ignition-switch issue [UPDATE]

UPDATE: A statement from GM about the recall has been added below. The exact total of vehicles affected is 3,296, including 3,073 of them in the US. General Motors isn't letting an ignition-switch problem grow into a massive scandal again. The automaker is recalling about 3,300 North American trucks and SUVs. They are: the 2014 Chevrolet Silverado and GMC Sierra and the 2015 Chevy Suburban and Chevy Tahoe, as well as 2015 model heavy-duty pickups, the Detroit News reports, citing an Associated Press story. The issue appears to have been caught fairly quickly. In this case, the keys can get stuck in the "start" position and then slip to "accessory" if bumped. This is because the ignition lock gears have an outer diameter that's larger than the specifications allow. When that happens the engine shuts off, and the driver loses assistance to the steering and brakes. The airbags might also be affected. The vehicles get a new ignition-lock housing to fix the problem. According to the Detroit News, an employee who experienced the problem with the switch discovered the issue, and this person then let officials at the automaker know as part of the Speak Up for Safety program. A total of five reports of the fault were discovered. However, there are no cases of injuries or crashes. The claims to the automaker's resolution program eventually tallied that GM's previous ignition switch problem included 124 deaths and 275 injuries. The company also had to recall millions of vehicles and pay significant fines to the US government. GM Statement General Motors is recalling 3,073 full-size trucks from the 2014 and 2015 model years in the U.S. Some of these vehicles may have an ignition lock actuator gear with an outer diameter that exceeds specifications, which may make turning the ignition key difficult. The ignition key could get stuck in the "start" position. This may be more likely at higher interior ambient temperatures. If the vehicle is driven with the key stuck in the "start" position, and the vehicle experiences a significant jarring event or the vehicle's interior temperature cools, the ignition lock cylinder could move out of the "start" position, rotate past the "run" position, and move into the "accessory" position, leading to loss of power steering assist, power brakes and potentially air bag deployment in certain crashes. Dealers will replace the ignition lock housing.

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck