66 Nova Chevy Ii Wagon Rat Rod on 2040-cars

Auto blog

Chevy's 6.6-liter Duramax is pretty much all new

To say there's a heated battle in heavy-duty pickups is an understatement, with Chevrolet, Ford, and Ram constantly trading blows of increased torque, horsepower, and towing capacity. The latest salvo is the revised, more powerful turbo diesel 6.6-liter Duramax V8 in the 2017 Chevy Silverado. It has 910 pound-feet of torque, an increase of 145, putting it nearly level with the Ford Super Duty. Here's a closer look at where those gains come from. How exactly did Chevrolet add all that torque plus 48 horsepower? The automaker essentially took a fine-tooth comb to the entire engine. Chevy says it changed 90 percent of the V8, and the cumulative effect of those small changes adds up to big increases. As you might guess, the turbocharger is updated. The larger unit features electric actuation of the variable nozzle turbine (VNT), and what Chevy calls a double axle cartridge mechanism that separates the VNT moving parts from the housing. That helps with heat performance as well, with a claim that the exhaust side of the turbo can run continuously up to 1,436 degrees Fahrenheit. Helping that cause are six exhaust gaskets made of Inconel - an nickel alloy that contains chromium and iron – and upgraded stainless steel for the exhaust manifold. Despite having the same cast iron cylinder block, albeit with some minor enhancements, the engine has new cylinder heads, pistons, piston pins, connecting rods, and crankshaft, which have all been upgraded to handle 20 percent higher cylinder pressures. Alongside the increase in pressure, Chevrolet also increased the cylinder head's structure with a honeycomb design. The pattern features high-strength aluminum with dual layer water jackets that not only improve strength, but also optimize water flow for better cooling. For 2017, the cylinder head also benefits from integrated plenum that aids the engine in getting more air under heavy loads. The cylinder head isn't the only component to get a minor update, as the pistons have a larger diameter pin for improved oil flow. The same detailed improvements has been bestowed to the humble connecting rods (second in our hearts only to the inanimate carbon rod). The new design has the bolts oriented roughly 45-degrees to the rod instead of parallel. The angle split design, as it's called allows for easier passage through the cylinder.

GM recalls 3,300 pickups and SUVs for new ignition-switch issue [UPDATE]

UPDATE: A statement from GM about the recall has been added below. The exact total of vehicles affected is 3,296, including 3,073 of them in the US. General Motors isn't letting an ignition-switch problem grow into a massive scandal again. The automaker is recalling about 3,300 North American trucks and SUVs. They are: the 2014 Chevrolet Silverado and GMC Sierra and the 2015 Chevy Suburban and Chevy Tahoe, as well as 2015 model heavy-duty pickups, the Detroit News reports, citing an Associated Press story. The issue appears to have been caught fairly quickly. In this case, the keys can get stuck in the "start" position and then slip to "accessory" if bumped. This is because the ignition lock gears have an outer diameter that's larger than the specifications allow. When that happens the engine shuts off, and the driver loses assistance to the steering and brakes. The airbags might also be affected. The vehicles get a new ignition-lock housing to fix the problem. According to the Detroit News, an employee who experienced the problem with the switch discovered the issue, and this person then let officials at the automaker know as part of the Speak Up for Safety program. A total of five reports of the fault were discovered. However, there are no cases of injuries or crashes. The claims to the automaker's resolution program eventually tallied that GM's previous ignition switch problem included 124 deaths and 275 injuries. The company also had to recall millions of vehicles and pay significant fines to the US government. GM Statement General Motors is recalling 3,073 full-size trucks from the 2014 and 2015 model years in the U.S. Some of these vehicles may have an ignition lock actuator gear with an outer diameter that exceeds specifications, which may make turning the ignition key difficult. The ignition key could get stuck in the "start" position. This may be more likely at higher interior ambient temperatures. If the vehicle is driven with the key stuck in the "start" position, and the vehicle experiences a significant jarring event or the vehicle's interior temperature cools, the ignition lock cylinder could move out of the "start" position, rotate past the "run" position, and move into the "accessory" position, leading to loss of power steering assist, power brakes and potentially air bag deployment in certain crashes. Dealers will replace the ignition lock housing.

This 450-hp electric Lotus Evora is powered by Tesla and Chevrolet

When someone mentions an electric Lotus, the first thing that comes to mind is the Tesla Roadster, the California-based automaker's first vehicle. That car started life as an Elise before being heavily massaged and adapted by Tesla's engineers. In a similar spirit, the people at Onpoint Dyno are close to finishing Blue Lightning, a track-ready all-electric Lotus Evora. Blue Lightning uses a Tesla drive unit and a Chevrolet Volt battery pack, both mounted in the middle in place of the Evora's 3.5-liter Toyota V6. It's putting down about 450 horsepower at the wheels. The car was built for time attack sessions, so power is fed through custom forged wheels and super sticky Pirelli PZero Trofeo R tires, the same ones found on the last Chevrolet Camaro Z/28. There is a custom digital instrument cluster in place of the Lotus gauges. There's also a regen paddle on the left side of the steering wheel. With a full charge, Blue Lighting should go about 120 miles. While the car runs under its own power, it's only about 90 percent complete. It has no power steering, no firewall in between the seats and the motor and battery pack, no A/C, and a large hole where the shift lever used to be. Other final touches include fine-tuning the brakes and suspension. There is also a custom rear bumper coming that should make it look more like the new Lotus Evora 400. Onpoint Dyno expects the car to hit the track in the next month or so. Related Video: