1967 Chevy Nova 4 Door on 2040-cars
Trinity, Alabama, United States
For Sale By:Private Seller
Engine:6 cylinder
Drive Type: manual
Make: Chevrolet
Mileage: 150,000
Model: Nova
Trim: base
you are looking on a 1967 chevy nova 4 door 6 cylinder manual transmission. runs good linkeage is messed up on the transmission. solid car minimal to no rust. this is a project needs restoration. no title you will receive a notarized bill of sale. there will be a mandatory nonrefundable $500 deposit required within 48 hours after auction ends any questions call 256-303-6098
Chevrolet Nova for Sale
1962 nova convertible(US $11,000.00)
1972 chevrolet nova yenko tribute car
1974 nova low mileage survivor
71 chevrolet nova small block,4 speed12 bolt super solid low mileage garage kept
1966 chevrolet nova wagon....ground up restoration..trades??
1966 chevy nova 2 dr ht,one family owned 100% rust free,100% orginal interior
Auto Services in Alabama
Vintage Automotive Repair ★★★★★
Townsend Automotive ★★★★★
Tim`s Foreign Car Services ★★★★★
Tigerstate Truck And Trailer ★★★★★
Thoroughbred Motor Cars ★★★★★
The Off-Road Connection ★★★★★
Auto blog
Next-gen Chevy Silverado and GMC Sierra may use carbon fiber
Thu, Dec 7 2017It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck
GM to squeeze out more production capacity for midsize trucks
Tue, May 26 2015General Motors was predicting a strong showing for the Chevrolet Colorado and GMC Canyon before they debuted, and demand among dealers for the midsize trucks even exceeded company's expectations. The positive situation has left GM with a problem, though: finding ways to increase capacity for the pickups at the Wentzville Assembly plant in Missiouri. With a third shift already running, GM has continued to look for ways to build just a few more of the trucks at the plant. The company has plans to hire as many as 1,000 more workers for the Saturday and Sunday shifts to construct an additional 2,000 pickups a month, according to unnamed insiders at the factory speaking to Automotive News. The little adjustments even extend to getting rid of an unpaid break to add 18 minute of assembly time over the course of a day, which equals about 3,500 more vehicles a year. All of this effort comes because the trucks are in such high demand. According to GM's figures, the company has delivered a combined 35,720 units of the Colorado and Canyon from January through April 2015, and the Chevy was the fastest-selling truck in the US for the previous three months. In May, it spent an average of just 12 days in showrooms before being snapped up. And even better for the company, 43 percent of these buyers came from other brands. According to Automotive News, the most popular trade-ins have included the Ford F-150, Toyota Tacoma, and Dodge Dakota. Related Video:
Chevy Crossvolt name kept alive in new trademark application
Fri, Dec 26 2014In April 2011 General Motors submitted a trademark application with the US Patent and Trademark Office for the word "Crossvolt." In November of this year, the application expired for lack of a statement of use. But in August of this year, GM applied again for the same trademark, leading some to believe that it intends to apply the name to a vehicle. That vehicle could explain the mule in sliced-and-diced Chevrolet Orlando bodywork caught in several spy shots this year, theorized to be some kind of Toyota Prius V or Ford C-Max Hybrid competitor; or it could be a production version of the Chevrolet Volt MP5 concept showed off at the Beijing Motor Show in 2010, which was about the same size as the Chevy Orlando. Or it could be none of those things – but the fact that Chevrolet is keeping it current makes us believe it will be... something. Featured Gallery Beijing 2010: Chevrolet Volt MPV5 concept View 13 Photos News Source: Fox News, Trademarkia Green Chevrolet GM Crossover Hybrid trademark uspto