1972 Montecarlomuseum Quality,44korig Miles,350v-8,auto,ac,ps,pb,build Sheet,exc on 2040-cars

Auto blog

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck

2014 Chevrolet Corvette Stingray convertible headed for Geneva debut

While most of the world is still coming down from all the hype surrounding the debut of the 2014 Chevrolet Corvette Stingray at the Detroit Auto Show earlier this month, we're already looking to the future. And according to Autoweek, the next chapter in the C7 story will unfold at the Geneva Motor Show in March. That's right, General Motors is reportedly using the Swiss stage as its venue to debut the Corvette Stingray convertible.
If this strikes you as odd, you aren't alone. After all, with a car that's such an American icon, we'd fully expect Chevrolet to unveil it here on our shores in either Chicago or New York. But according to Autoweek, GM is looking to boost export sales of its halo car, and since the C7 was engineered to compete with the world's best and brightest, showing it off in Geneva is somewhat of a smart move. What's more, those with sharp memories will recall that GM used the Geneva expo to debut the sixth-generation C6 Corvette convertible back in March 2004, so there's also a precedent.
Details surrounding the Corvette Stingray convertible are still slim, though we fully expect the 6.2-liter V8 and choice of either six-speed automatic or seven-speed manual transmissions to carry over unchanged. Prototypes spotted on the road showed the car fitted with a cloth convertible roof, as well.

Next-gen Chevy Cruze caught cruising in the cold

Spy photographers have caught what looks like the next-generation Chevrolet Cruze out on snow patrol. The camo could be tricking our eyes, but it look like it has an even tidier, more rounded front end and even lower fenders in relation to the top of the hood. And either a chunk of camo has been wedged between the side mirrors and the doors, or the mirrors are up for revision, too.
The door handles have been moved up the side of the car, leading the way to a rear end that grows a bit in length. If the rumors are true, the coming second-generation Cruze sits on the new D2XX platform that will replace the Delta and Theta platforms at General Motors. A global architecture, the Cruze will be the first to get it, but it will underpin everything from next Chevrolet Volt to the Equinox and could be responsible for 2.5 million units by 2018. The next Cruze is expected to begin production in GM's Lordstown, Ohio plant in the third quarter of 2014.