2010 Chevy Malibu Lt Sedan Salvage Repairable Project Flood Loaded Water Damage on 2040-cars

Auto blog

Driving Granatelli's turbine-powered 1978 Chevy Corvette [w/video]

With its curvy snout and feminine haunches, the third-gen Chevrolet Corvette looks like a dreamy – if dated – exemplar of Sports Car Fantasy 101 when viewed through modern eyes. This particular specimen circa '78, clad in silver and black paint with red pinstripes, appears to be a well-preserved example from the era. Apart from its low-profile Pirellis, slightly raised and slotted hood, spacious stance and a certain hand-painted descriptor alongside its crossed flag logos, you'd never guess there's a Space-Age propulsion unit powering this Coke bottle-bodied ride. Climb inside, and you're presented with aircraft gauges and big, colorful square buttons in the center panel. It takes a push of the "Ignitor" button, a tap of the starter button, and a slide of a T-handle for this nearly 40-year-old sports car to start sounding like Gulfstream G650 ready for takeoff. Yep, you're sitting in an 880-horsepower, turbine-powered Corvette, the only one of its kind in the world. Welcome to the whoosh. What The...? Built by Vince Granatelli, son of Indy 500 guru Andy Granatelli, this curious Corvette came into being by cramming a Pratt & Whitney ST6N-74 gas turbine engine into the donor car's lengthy front end. The same type of Jet A-burning mill powered Granatelli Senior's STP-sponsored racecar at the 1967 Indianapolis 500, where it famously led most of the 198 of 200 laps until a $6 transmission bearing failed, knocking it out of the race. The idea of turbine power usurping internal combustion was so threatening that Indy's governing body restricted turbine performance into obsolescence thereafter. A turbine-powered Corvette sounds excessive because it is. But there are also things about this 880-horsepower, 1,161-pound-feet monster that might surprise you. While it smacks of futurist exoticism and cost a then-dizzying $37,000 in 1967, the Canadian-built powerplant uses 80 percent fewer parts than an internal combustion V8 and will run on virtually anything combustible – whiskey, diesel, even Chanel No. 5. Though it's triple the length of a V8, the Pratt & Whitney beast weighs only 285 pounds. It's also one hell of a robust workhorse, typically serving as an auxiliary power unit for commercial aircraft or a generator in oil fields, where it can run for tens of thousands of consecutive hours before needing an overhaul. To adapt the Chevrolet for jet duty, the nose section was gutted and a sub-frame was built to compensate for the loosey-goosey front end.

2021 Chevy Colorado and GMC Canyon facelift spied

The Chevy Colorado and its GMC Canyon twin have been on sale for a good long time now, and while things move a little more slowly on the truck side when it comes to facelifts and model changeovers, it seems like it’s about time. So itÂ’s no surprise to see some lightly camouflaged trucks running around ahead of what appears to be a minor refresh for the 2021 model year. Starting with the Colorado, it appears to have a bowtie hiding behind some camo in the center of the grille, which otherwise looks like the no-bowtie option you can get on 2019-and-up trucks. It could be that Chevy is keeping the no-bowtie grille design but allowing a bowtie to grace it, or it could be misdirection. Either way, the grille pattern adds a bit of flair to the otherwise staid front end design. There also appears to be a bit more shape to the lower air inlet, with echoes of some of the lower fascias of its bigger Silverado stablemate. The Canyon, on the other hand, shows more extensive front-end changes. At first glance, it looks to emulate some variants of the GMC Sierra, which would make sense given those modelsÂ’ changes for the 2020 model year. In particular, this Canyon has hints of Sierra HD, being more square and monolithic than the regular Sierra 1500s, although itÂ’s a little hard to tell with the camo covering the edges of the grille. It could certainly also adopt more rounded corners like the 1500s. Either way, itÂ’s more vertical and thereÂ’s less differentiation between the upper grille and lower opening. ThereÂ’s nothing in the way of changes around the sides or back, and while there may be some minor changes inside, we arenÂ’t expecting any. The word around town is that this isnÂ’t a full facelift, but rather a minor front end tweak thatÂ’ll just be a regular part of the model-year changeover. 

Just the right Camaro can change your life

Not many people can say that their car directly motivated them into a career, but that's exactly the case for Adam Martin and his 1968 Chevrolet Camaro that he calls Lucy. Martin bought the pony car in primer when he was just 16, and it helped foster his profession in restoring classic cars. Beyond just being a very cool ride for a teenager, every change to Lucy was an opportunity to hone a new automotive skill for Martin. Whether figuring out how to paint a car or building the 454-cubic-inch (7.4-liter) big block V8, the Camaro offered a platform for experimentation. This latest episode of Petrolicious gets personal about the bond between man and machine for this 18-year ongoing project. And even if the story doesn't immediately grab you, Lucy has a great voice and can do a mean burnout. News Source: Petrolicious via YouTube Chevrolet Maintenance Ownership Coupe Performance Classics Videos petrolicious