1963 Chevrolet Impala Ss, Rat Rod,low Rider,hot Rod,custom,classic,62,61,64 on 2040-cars

Auto blog

2014 Chevrolet SS makes its live debut

Chevrolet showed off the new 2014 SS in an airport hangar last night, its first rear-wheel-drive performance sedan in the US since the Impala SS from 1997. We'll have more to say about the SS later today, but this is the sedan that Chevrolet sees as the final piece in restoring its performance credentials. For those of you looking for a manual transmission, however, that wish will go unfulfilled - at least for now: the only two options buyers will have are the color and whether or not they want a sunroof.
We'll work on getting some more angles (in better light) today at Daytona International Speedway, but with fans seeing the car for the first time, we don't hold out much luck of getting a clear shot. So for now, enjoy the high-res gallery above.

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck

GM struggles to sell small cars, plans to lay off 2,084 employees at two plants

Due to low demand for some of its vehicles, General Motors plans to cut 2,084 jobs at its assembly plants in Lordstown, OH and Lansing, MI. At the same time, the automaker also announced plans to invest approximately $900 million in three of its facilities – the Toledo Transmission Operations in Ohio, Bedford Casting Operations in Indiana, and Lansing Grand River in Michigan - for future products. GM will discontinue the third shift at both the Lansing Grand River plant and the Lordstown, OH plant. The Cadillac ATS, Cadillac CTS, and Chevrolet Camaro are made at the automaker's plant in Michigan, which currently has 2,700 employees. The move to eliminate the third shift affects 810 hourly workers, as well as 29 salaried employees, starting on January 16th. The plant in Lordstown, OH currently has 4,500 employees and makes the Chevrolet Cruze sedan. The plan to discontinue the third shift will affect 43 salaried workers and 1,202 hourly employees and will start on January 23rd. As Fortune points out, sales of the Cruze are down 20 percent through October, while sales of the Cadillac ATS and CTS were down 17 percent through the same period of time. In addition to cutting the third shift at both assembly plants, the automaker plans to invest a total of $900 million between three of its facilities for unnamed future products. GM's Toledo Transmission Operations will receive $667.6 million, the Lansing Grand River Assembly plant will receive $211 million, and the automaker's Bedford Casting Operations will get $37 million. Last year, GM cut roughly 500 jobs from its Orion Township factory due to slow sales of the Chevrolet Sonic and Buick Verano, with surging crossover and SUV sales as the most likely culprit. With GM posting much healthier sales figures for the Chevrolet Equinox and Cadillac XT5 compared to the ATS, CTS, and Cruze, it looks like compact SUVs are to blame for this year's layoffs as well. Related Video: News Source: Fortune, General MotorsImage Credit: REUTERS / Rebecca Cook Hirings/Firings/Layoffs Plants/Manufacturing Cadillac Chevrolet GM Coupe Sedan Lordstown Ohio