Fl One Owner Low Miles Gorgeous Condition Starcraft Conversion Dual Ac 5.7 G20 on 2040-cars

Auto blog

GM reintroduces Tripower name in the worst way possible

The story of General Motors' use of the Tripower moniker begins way back in 1957, when Semon E. "Bunkie" Knudsen, then General Manager of GM's Pontiac division, directed his engineers to inject more performance into his brand's line of V8-powered automobiles. Fuel injection was an option, but hot rodders flocked instead to Tri-Power (marketed way back when with a hyphen), which grafted a trio of two-barrel Rochester carburetors onto a single intake manifold. A legend was born. And that legend was born of performance. At idle and when full power wasn't required, Pontiac's Tri-Power system used just the middle carburetor, which helped make the setup easier to tune. Depending on the year and model, either a vacuum system or a mechanical linkage opened up the two outer carbs, thereby switching from two barrels to six, and allowing the engine to take in more fuel and air. And it was an easy marketing win – six barrels is better than four barrels, right? Because performance! So, when news filtered in that GM has resurrected the Tripower name, those of us who grew up attending classic car shows and wrenching on old Pontiacs did a double-take. And then we all collectively sighed. Turns out that today's Tripower refers to a trio of fuel-saving measures that include cylinder deactivation, active thermal management, and intake valve lift control, according to Automotive News. And, at least for now, it applies to GM's line of fullsize trucks powered by a 2.7-liter turbocharged four-cylinder engine. We're all for saving fuel whenever possible. And we have zero say in how any automaker chooses to market its products and technologies. But, we'll offer our two cents anyway: Relaunching a storied name from the past is fine. Relaunching a storied name from the past while completely overlooking the reasons the name got famous in the first place is only going to irritate the people who remember the name in the first place. Couldn't they just call this new technology package something else? Related Video: News Source: Automotive NewsImage Credit: Getty Green Marketing/Advertising Chevrolet GM Pontiac Automotive History Truck chevrolet silverado

Bob Lutz builds the case for a mid-engined Corvette

Rumors of a mid-engine Corvette are like automotive industry folklore at this point. Every once in a while, news pops up that it might be happening or is under development, but nothing actually ever comes to fruition as something people can actually buy. The latest spy shots strongly suggest a mid-engine 'Vette is in the cards, yet again, possibly for 2018. Now, an op ed by former General Motors executive (and definite performance car fan) Bob Lutz in Road & Track gives the inside scoop on the history of one of these proposals and lays out how to make it happen today. According to Lutz, the company's engineers believed the C6 ZR1 was at the limit for front-engine, rear-wheel drive performance in that package, and the only solution was to move the powerplant behind the driver. Lutz even got then CEO Rick Wagoner on board. The scheme made it at least as far as clay models for mid-engine versions of the 'Vette and Cadillac XLR. Eventually, a lack of money got in the way, though, bringing the project to an end. Lutz puts a lot of faith in GM's current leaders, especially Mary Barra and Mark Reuss. He thinks the chances of a mid-engine 'Vette happening this time are better than 50 percent. The model, rumored to be named Zora, could offer over 700 horsepower in an ultra lightweight body and be priced at about $120,000 to "suck the doors off everybody." Head over to Road & Track to get some insights from this highly respected and entertaining auto industry veteran. Related Video:

GM, UAW poaching Nissan workers in Tennessee

General Motors and the United Auto Workers are going on a recruitment drive at the Spring Hill factory in Tennessee, and they're hoping to poach some skilled workers from Nissan's nearby plant in Smyrna, TN. The General and the union even bought a billboard advertising for industrial electricians near the Japanese automaker's facility, according to the Daily News Journal. The reason for the billboard was simple. "GM was short of electricians," said Tim Stannard, the president of the UAW local at Spring Hill, to the Daily News Journal. The factory currently builds the Chevrolet Equinox but has a contract to assemble the next generation of Ecotec engines and the Cadillac XT5, which replaces the SRX. Thanks to the $185-million deal, employment there is expected to double by May 2016, according to Stannard, with roughly 1,800 additional union jobs. Beyond just several billboards, GM has job postings online for the Spring Hill plant looking for workers with specific skills. There has already been some interest in the positions among Nissan employees, Stannard indicated. According to a recent study by the Center for Automotive Research, the average GM worker currently makes $58 an hour, including benefits. Comparatively, Nissan pays an average of $42 an hour with benefits. The General's number could change in the coming weeks because its contract with the UAW is about to expire, and higher wages are among the major negotiating points.