2004 Chevrolet Express 1500 Wheelchair Passenger Van 3-door 5.3l (black) on 2040-cars

Auto blog

Driving Granatelli's turbine-powered 1978 Chevy Corvette [w/video]

With its curvy snout and feminine haunches, the third-gen Chevrolet Corvette looks like a dreamy – if dated – exemplar of Sports Car Fantasy 101 when viewed through modern eyes. This particular specimen circa '78, clad in silver and black paint with red pinstripes, appears to be a well-preserved example from the era. Apart from its low-profile Pirellis, slightly raised and slotted hood, spacious stance and a certain hand-painted descriptor alongside its crossed flag logos, you'd never guess there's a Space-Age propulsion unit powering this Coke bottle-bodied ride. Climb inside, and you're presented with aircraft gauges and big, colorful square buttons in the center panel. It takes a push of the "Ignitor" button, a tap of the starter button, and a slide of a T-handle for this nearly 40-year-old sports car to start sounding like Gulfstream G650 ready for takeoff. Yep, you're sitting in an 880-horsepower, turbine-powered Corvette, the only one of its kind in the world. Welcome to the whoosh. What The...? Built by Vince Granatelli, son of Indy 500 guru Andy Granatelli, this curious Corvette came into being by cramming a Pratt & Whitney ST6N-74 gas turbine engine into the donor car's lengthy front end. The same type of Jet A-burning mill powered Granatelli Senior's STP-sponsored racecar at the 1967 Indianapolis 500, where it famously led most of the 198 of 200 laps until a $6 transmission bearing failed, knocking it out of the race. The idea of turbine power usurping internal combustion was so threatening that Indy's governing body restricted turbine performance into obsolescence thereafter. A turbine-powered Corvette sounds excessive because it is. But there are also things about this 880-horsepower, 1,161-pound-feet monster that might surprise you. While it smacks of futurist exoticism and cost a then-dizzying $37,000 in 1967, the Canadian-built powerplant uses 80 percent fewer parts than an internal combustion V8 and will run on virtually anything combustible – whiskey, diesel, even Chanel No. 5. Though it's triple the length of a V8, the Pratt & Whitney beast weighs only 285 pounds. It's also one hell of a robust workhorse, typically serving as an auxiliary power unit for commercial aircraft or a generator in oil fields, where it can run for tens of thousands of consecutive hours before needing an overhaul. To adapt the Chevrolet for jet duty, the nose section was gutted and a sub-frame was built to compensate for the loosey-goosey front end.

GM reintroduces Tripower name in the worst way possible

The story of General Motors' use of the Tripower moniker begins way back in 1957, when Semon E. "Bunkie" Knudsen, then General Manager of GM's Pontiac division, directed his engineers to inject more performance into his brand's line of V8-powered automobiles. Fuel injection was an option, but hot rodders flocked instead to Tri-Power (marketed way back when with a hyphen), which grafted a trio of two-barrel Rochester carburetors onto a single intake manifold. A legend was born. And that legend was born of performance. At idle and when full power wasn't required, Pontiac's Tri-Power system used just the middle carburetor, which helped make the setup easier to tune. Depending on the year and model, either a vacuum system or a mechanical linkage opened up the two outer carbs, thereby switching from two barrels to six, and allowing the engine to take in more fuel and air. And it was an easy marketing win – six barrels is better than four barrels, right? Because performance! So, when news filtered in that GM has resurrected the Tripower name, those of us who grew up attending classic car shows and wrenching on old Pontiacs did a double-take. And then we all collectively sighed. Turns out that today's Tripower refers to a trio of fuel-saving measures that include cylinder deactivation, active thermal management, and intake valve lift control, according to Automotive News. And, at least for now, it applies to GM's line of fullsize trucks powered by a 2.7-liter turbocharged four-cylinder engine. We're all for saving fuel whenever possible. And we have zero say in how any automaker chooses to market its products and technologies. But, we'll offer our two cents anyway: Relaunching a storied name from the past is fine. Relaunching a storied name from the past while completely overlooking the reasons the name got famous in the first place is only going to irritate the people who remember the name in the first place. Couldn't they just call this new technology package something else? Related Video: News Source: Automotive NewsImage Credit: Getty Green Marketing/Advertising Chevrolet GM Pontiac Automotive History Truck chevrolet silverado

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck