2003 Chevrolet Express Hitop Conversion Van on 2040-cars

Auto blog

Chevy's 6.6-liter Duramax is pretty much all new

To say there's a heated battle in heavy-duty pickups is an understatement, with Chevrolet, Ford, and Ram constantly trading blows of increased torque, horsepower, and towing capacity. The latest salvo is the revised, more powerful turbo diesel 6.6-liter Duramax V8 in the 2017 Chevy Silverado. It has 910 pound-feet of torque, an increase of 145, putting it nearly level with the Ford Super Duty. Here's a closer look at where those gains come from. How exactly did Chevrolet add all that torque plus 48 horsepower? The automaker essentially took a fine-tooth comb to the entire engine. Chevy says it changed 90 percent of the V8, and the cumulative effect of those small changes adds up to big increases. As you might guess, the turbocharger is updated. The larger unit features electric actuation of the variable nozzle turbine (VNT), and what Chevy calls a double axle cartridge mechanism that separates the VNT moving parts from the housing. That helps with heat performance as well, with a claim that the exhaust side of the turbo can run continuously up to 1,436 degrees Fahrenheit. Helping that cause are six exhaust gaskets made of Inconel - an nickel alloy that contains chromium and iron – and upgraded stainless steel for the exhaust manifold. Despite having the same cast iron cylinder block, albeit with some minor enhancements, the engine has new cylinder heads, pistons, piston pins, connecting rods, and crankshaft, which have all been upgraded to handle 20 percent higher cylinder pressures. Alongside the increase in pressure, Chevrolet also increased the cylinder head's structure with a honeycomb design. The pattern features high-strength aluminum with dual layer water jackets that not only improve strength, but also optimize water flow for better cooling. For 2017, the cylinder head also benefits from integrated plenum that aids the engine in getting more air under heavy loads. The cylinder head isn't the only component to get a minor update, as the pistons have a larger diameter pin for improved oil flow. The same detailed improvements has been bestowed to the humble connecting rods (second in our hearts only to the inanimate carbon rod). The new design has the bolts oriented roughly 45-degrees to the rod instead of parallel. The angle split design, as it's called allows for easier passage through the cylinder.

Consumer Reports criticizes small turbo engines for misleading performance, fuel economy claims [w/video]

Consumer Reports has taken aim at at small-displacement, forced-induction engines, saying the powerplants don't manage to deliver on automaker fuel economy claims. Manufacturers have long held that smaller, turbocharged engines pack all power of their larger displacement cousins with significantly better fuel economy, but the research organization says that despite scoring high EPA economy numbers, the engines are no better than conventional drivetrains in both categories. Jake Fisher, director of automotive testing for Consumer Reports, says the forced induction options "are often slower and less fuel efficient than larger four and six-cylinder engines."
Specifically, CR calls out the new Ford Fusion equipped with the automaker's Ecoboost 1.6-liter four-cylinder engine. The institute's researchers found the engine, which is a $795 option over the base 2.5-liter four-cylinder, fails to match competitors in acceleration and served up 25 miles per gallon in testing, putting the sedan dead last among other midsize options.
The Chevrolet Cruze, Hyundai Sonata Turbo and Ford Escape 2.0T all got dinged for the same troubles, though Consumer Reports has found the turbo 2.0-liter four-cylinder in the BMW 328i does deliver on its promises. You can check out the full press release below. You can also read the full study on the Consumer Reports site, or scroll down for a short video recap.

Even if GM does close all 5 of those plants, it'll still have too many

DETROIT — General Motors' monumental announcement on Monday that it will close three car assembly plants and two powertrain plants in North America and slash its workforce will only partially close the gap between capacity and demand for the automaker's sedans, according to a Reuters analysis of industry production and capacity data. Sales of traditional passenger cars in North America have been declining for the past six years and are still withering. After GM ends production next year at factories in Michigan, Ohio and Ontario, it will still have four U.S. passenger-car plants — all operating at less than 50 percent of rated capacity, according to figures supplied by LMC Automotive. In comparison, Detroit-based rivals Ford and Fiat Chrysler Automobiles will have one car plant each in North America after 2019. The Detroit Three are facing rapidly dwindling demand for traditional passenger cars from U.S. consumers, many of whom have shifted to crossovers and trucks. Passenger cars accounted for 48 percent of retail light-vehicle sales in the United States in 2014, according to market researchers at J.D. Power and Associates. This year, sedans will account for less than a third of light vehicle sales. That shift in turn has left most North American car plants operating far below their rated capacities, while many SUV and truck plants are running on overtime. The collapse in passenger-car demand is a challenge for nearly all automakers in the United States, including Japan's Toyota and Honda, which have the top-selling models in the compact and midsize car segments. Toyota executives said last month they are evaluating the company's U.S. model lineup. But Toyota also plans to build compact Corolla sedans at a new $1.6 billion factory it is building in Alabama with partner Mazda. The obstacles facing GM in its plans to close more auto factories became apparent on Tuesday as U.S. President Donald Trump threatened to block payment of government electric vehicle subsidies to GM. While it is not certain that Trump unilaterally has the power to do that, he made it clear he intends to use his office to pressure the company to keep open a small car plant in Ohio that GM says will stop building vehicles in March.