2003 Chevrolet Express 3500 Base Cutaway Van 2-door 6.0l on 2040-cars

Auto blog

Porsche wins the 2015 24 Hours of Le Mans

The question going into this year's 24 Hours of Le Mans was whether or not the Porsche 919 Hybrid would be able to combine its qualifying pace with race reliability. After battling neck-and-neck with Audi's R18 for most of the race, the answer is a resounding yes. Not only did Porsche drivers climb the first two spots on the podium, they did so without any major mishaps on track. This win is the first overall trophy for Porsche since 1998. Audi previously won the last five races, and 13 of the last 15. Corvette also returned to the winner's circle, with the No. 64 C7.R taking winning the GTE Pro division. The victory is the first class win for Corvette since 2011. KCMG won the LMP2 class in ninth overall. With 45 minutes to go the No. 98 Aston Martin crashed out of first place in GTE Amateur, giving the class win to SMP Racing's Ferrari and second place to the Patrick Dempsey Racing Porsche 911 RSR. For the full list of official results, click here. The GTE Pro class proved to be just as exciting as the P1 class, with a four-way battle for first after four hours into the race. For most of the race, the battle at the top went back and forth between the two German manufacturers. An tire puncture in the No. 7 Audi gave up the lead to Porsche, and moments later a crash forced the No. 8 into the garage. But a three-minute replacement of the front and rear bodywork kept the Audi in contention. As the race wore into the night, Porsche maintained a slightly faster pace than Audi. Nick Tandy took the lead on Lap 253 early Sunday morning, and car No. 19 never gave up the top position. The win is the first for all three drivers of the No. 19 – Nico Hulkenberg, Earl Bamber, and Nick Tandy. A lap behind in second was the No. 17 Porsche. The Audis fought reliability problems late in the race but still finished third with the No. 7 R18. The GTE Pro class proved to be just as exciting as the P1 class, with a four-way battle for first after four hours into the race. As the Aston Martin cars dropped away, the lone Corvette Racing entry took over, followed by a charging AF Corse team Ferrari 458 Italia. The Corvette and Ferrari continued to trade places in the final hours until gearbox trouble forced the No. 51 Ferrari out of contention. It was eventually passed by the other AF Corse car, No. 71. Nissan experienced all the pain of a first-year effort with its front-wheel-drive GT-R LM Nismo.

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck

Surprise! GM putting aluminum in next-gen pickups

Last month, General Motors launched a series of ads touting the benefits of steel over aluminum – specifically, with regard to the Chevy Silverado versus the Ford F-150. (Kind of. We're not sure what a grizzly bear has to do with anything.) We took issue with the ads, with editor in chief Mike Austin saying they "reek of insecurity, and distract from the Silverado's strengths that could be used for positive advertising." But what bothers us more, is that yet another report surfaced claiming anti-aluminum GM will indeed use the weight-saving material in its next-generation fullsize trucks. On Tuesday, GM announced a $877-million investment for its truck plant in Flint, MI. But Reuters says that huge overhaul is because the trucks will use "substantially different equipment than the tools GM uses today." The report specifically states, "People familiar with the company's plans say GM's next-generation pickups and SUVs will make use of various materials, including aluminum and lightweight steel, to shed weight and gain fuel efficiency to meet tougher federal standards." The Silverado already uses a few aluminum components in the engine and hood, and if more widespread use will help GM build its best fullsize trucks ever, then that's great. Honestly, we have no reason to doubt that aluminum will be used in the next Silverado and GMC Sierra. We just hope GM remembers that nothing is ever truly deleted from the bowels of the Internet when it launches the subsequent "look how great aluminum is!" campaign. Related Video: News Source: Reuters Green Plants/Manufacturing Chevrolet GM GMC Truck aluminum steel