06 Chev Express 1500 Cargo - Clean Florida Van - Runs Good - Cold Ac on 2040-cars

Auto blog

More Corvette Stingray Factoids: Vanishing panel gaps and 26-mpg LT1

During January's Detroit Auto Show, we managed a longer than expected wandering tag-team interview with C7 Corvette chief engineering exec Tadge Juechter (pictured above), and LT1 engine boss Jordan Lee (pictured below). They are, quite honestly, two of the very nicest bigshot lads to ever walk the engineering corridors of an American manufacturer. Both are enthralled by what they're doing for a day job. So are we.
We've followed the pre-sale anticipation for the Chevrolet C7 Corvette Stingray like an Oreck vacuum yanking every speck of dirt from a well-trampled carpet. Everything is reportable and contains a grain of further knowledge about this dramatically important and cheered-for car, as it continues to be pressured into representing all that is superior about the American dream. The Corvette wears one heavy cloak.
So, most of what was talked about has been expertly reported already right here on Autoblog. But, looking through our notes again, both Jeuchter and Lee added facts to the buzzing mix.

Why does the Corvette Stingray have so many vents? Here's why

Just looking at the new 2014 Chevrolet Corvette Stingray, it's not hard to see that the car's design was created with aerodynamics at the forefront, but Chevrolet designers point out exactly what went into designing the iconic coupe in a pair of recently released videos. The videos show the Corvette going through early design phases, including clay models and wind tunnel tests, as well as talking to the car's chief engineer, Tadge Juechter.
Both videos help explain various aspects of the C7 Corvette, but it's the aero tuning of the car that is most interesting. This includes extra attention paid to the lower air dam and vented hood to help reduce drag and lift, while the rear quarter inlets are for differential and transmission cooling. Juechter said that some of these aero-tuned elements were inspired from GM's involvement in racing.
If you have about five minutes and you can't get enough information about the new 'Vette, then check out the videos posted below.

GM won't really kill off the Chevy Volt and Cadillac CT6, will it?

General Motors is apparently considering killing off six slow-selling models by 2020, according to Reuters. But is that really likely? The news is mentioned in a story where UAW president Dennis Williams notes that slumping US car sales could threaten jobs at low-volume factories. Still, we're skeptical that GM is really serious about killing those cars. Reuters specifically calls out the Buick LaCrosse, Cadillac CT6, Cadillac XTS, Chevrolet Impala, Chevrolet Sonic, and the Chevrolet Volt. Most of these have been redesigned or refreshed within the past few model years. Four - the LaCrosse, Impala, CT6, and Volt - are built in the Hamtramck factory in Detroit. That plant has made only 35,000 cars this year - down 32 percent from 2016. A typical GM plant builds 200,000-300,000 vehicles a year. Of all the cars Williams listed, killing the XTS, Impala, and Sonic make the most sense. They're older and don't sell particularly well. On the other hand, axing the other three seems like an odd move. It would leave Buick and Cadillac without flagship sedans, at least until the rumored Cadillac CT8 arrives. The CT6 was a big investment for GM and backing out after just a few years would be a huge loss. It also uses GM's latest and best materials and technology, making us even more skeptical. The Volt is a hugely important car for Chevrolet, and supplementing it with a crossover makes more sense than replacing it with one. Offering one model with a range of powertrain variants like the Hyundai Ioniq and Toyota Prius might be another route GM could take. All six of these vehicles are sedans, Yes, crossover sales are booming, but there's still a huge market for cars. Backing away from these would be essentially giving up sales to competitors from around the globe. The UAW might simply be publicly pushing GM to move crossover production to Hamtramck to avoid closing the plant and laying off workers. Sales of passenger cars are down across both GM and the industry. Consolidating production in other plants and closing Hamtramck rather than having a single facility focus on sedans might make more sense from a business perspective. GM is also trying to reduce its unsold inventory, meaning current production may be slowed or halted while current cars move into customer hands. There's a lot of politics that goes into building a car. GM wants to do what makes the most sense from a business perspective, while the UAW doesn't workers to lose their jobs when a factory closes.