2014 Chevrolet Equinox Ltz on 2040-cars

Auto blog

1983 Motorweek showdown pits Porsche 928S vs. Chevy Camaro Z28

Last month, Motor Trend threw the Camaro Z/28 and Porsche 911 GT3 into the bear pit and let them fight it out. Way back in 1983, MotorWeek had the same idea, comparing the Camaro Z/28 to the Porsche 928S. At the time, the Camaro was America's best selling sports coupe, the 928S was Porsche's top-of-the-line model that also had the highest top speed of any car sold here. And the price differential was even more stark then: $13,600 for the Camaro, $45,000 for the Porsche. That put the Z/28's cast-iron, 5.0-liter V8 with 190 horsepower and 240 pound-feet of torque against the all-aluminum 4.7-liter V8 with 234 hp and 263 lb-ft in the 928S. Even with that and the Camaro being 14 inches longer than the Porsche, the American was a surprising 40 pounds lighter than the German. The show took them to Summit Point Raceway in West Virginia to see how close a relative performance bargain could hang with a the German GT. Both had five-speed manual transmissions, but the high-speed corners and tight sections of Summit Point would test other handling variables, including the "bone-rattling" Camaro's solid rear axle and disc and drum brake setup vis-a-vis the four-wheel disc brakes and independent suspension on the "firm-but-smooth" Porsche. Paradoxically, the larger disparity 22 years ago resulted in a closer result. Check out the video to see how the Summit was won. News Source: MotorWeek via YouTube Chevrolet Porsche Coupe Luxury Performance Classics Videos chevy camaro z28 porsche 928 retro review

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck

The Opel GT is the concept General Motors should build for the US

Now is the time. General Motors should double-down on performance cars and build the Opel GT concept that's set to debut next week at the Geneva Motor Show. Better yet, sell it in the United States as the Chevy GT. Consumers are showing a thirst for performance cars not seen in decades. Ford has them coming in waves, with everything from the F-150 Raptor to a hotted-up Fusion. FCA US is unrepentantly building loads of Hellcats. GM should respond. The General's cupboard is hardly bare. With the Corvette, Camaro, and Cadillac's V-Series, GM has more than enough to compete with its crosstown rivals and anything Europe or Japan can throw at it. But there's also an opportunity. There's not many front-mid-engine, rear-wheel-drive, two-seat sports cars out there like the Opel GT concept. A Chevy GT that used that layout and captured some of the concept car's proportions and curves would ignite a different kind of passion in enthusiasts. It would be Miata-like. With Chevy branding, this sports car would be the everyday exotic. The concept has a turbocharged 1.0-liter three-cylinder engine, which makes about 143 horsepower to motivate a structure that weighs less than 2,200 pounds. It can hit 60 miles per hour in less than eight seconds. All of those numbers are within the front-engined Miata's territory. This new Opel is inspired by two great mid-1960s concepts that helped put its design studio, and that of its sister brand, the British Vauxhall, on the map. (The GT concept is also technically a Vauxhall, as the brands are linked in GM's European strategy.) One of them, the '66 Vauxhall XVR remained a concept. The '65 Opel Experimental GT was on the road by 1968. That shows this is doable. There's precedent. The Saturn Sky and Pontiac Solstice shared a chassis with a modern GT during that trio's brief run. If GM ever makes this concept, Opel and Vauxhall should get their versions. But Chevy is the one that could make this car a global icon. Chevrolet GT. Make it happen. News & Analysis News: The potential return of the Ford Bronco is generating a ton of attention. Analysis: That's not news, per se. But when the Bronco6G.com fan site did a rendering of a next-generation Bronco, it almost broke the Internet. Everyone from Automotive News to Jalopnik picked up the illustrations. Our own post has drawn a lot of traffic and passionate responses. People are clamoring for the Bronco's return.