1981 Chevrolet El Camino Conquista, New Paint, New 350 V8, Rebuilt Transmission on 2040-cars

Auto blog

Former Fisker CEO has some advice for Tesla Motors

Former Fisker Automotive CEO and ex-Chevrolet Volt vehicle-line director Tony Posawatz has some words of caution for Tesla Motors. The long-time automaker executive questions the California automaker's long-term viability – and gives some praise – in a talk with Benzinga, which you can listen to below. While the all-wheel-drive D that Tesla unveiled earlier this month in Southern California wowed a packed crowd, Posawatz (starting at around minute 4:45 in the interview) says Tesla would've been better off taking the resources it expended toward that Model S upgrade and directed them towards speeding up the development of a more affordable plug-in. Perhaps a number of investors agreed, since the company's stock fell the day after the D was announced. Posawatz says Tesla has been over-reliant on the sale of ZEV credits. Posawatz also says that Tesla has been over-reliant on the sale of zero-emissions vehicle credits in California for its earnings and questions whether the automaker will ever work at a large enough scale to sufficiently drive down costs and make consistent profits. Tesla CEO Elon Musk would take issue with this characterization. Posawatz first made his mark in the plug-in vehicle world when he was the vehicle-line director at General Motors for the Volt extended-range plug-in from 2006 to 2012. Later that year, he joined extended-range plug-in maker Fisker Automotive as its CEO, though quit that job during the summer of 2013 as the company was descending into insolvency. He joined the Electrification Coalition this past March. News Source: Benzinga Green Chevrolet Fisker Tesla Electric PHEV Tony Posawatz

Fewer than 1 in 3 Chevy dealers earn right to initially sell C7 Corvette

Looking to make the launch of the 2014 Corvette Stingray as efficient as possible, Chevrolet will be limiting the numbers of its dealers that can sell the all-new coupe and convertible. According to Automotive News, sales of the C7 Corvette will initially be limited to less than a third of Chevy's total dealership network when the 'Vette goes on sale this summer.
Only 900 dealers out of more than 3,000 locations nationwide will be allowed to sell the new Corvette at first, and the reason for this is so that there are no shortages at dealers that can actually get the cars sold. The article says that the 900 dealerships chosen represented 80 percent of total Corvette sales in 2012.
Some of the requirements dealers had to make to get initial allocation of Stingray sales include having sold at least four Corvettes in 2012 and having a Corvette Stingray specialist who will be required to have gone through a training session costing more than $2,000 per attendee. Once demand for the 2014 Corvette Stingray begins to subside - approximately six to nine months after it goes on sale - then allocation could open up to more dealers, but the report indicates this could happen following the 2014 model year.

GM patent reveals new two-stage turbocharger

Modern turbochargers may be some of the best ever made, but performance is something that engineers are always trying to improve. According to GM Inside News, General Motors (GM) is hoping to alleviate some of the negative aspects of a two-stage turbocharger setup with a newly-patented design. The patent, that was filed on May 19, 2016, reveals a clever bypass system that allows the engine, a four-cylinder unit, to optimize both the low-pressure and high-pressure inlets for its respective functions. According to the filing, a conventional two-stage turbocharger setup is engineered to allow both turbines to operate simultaneously at low and mid engine speeds. At high engine speeds, only the low-pressure turbine works. The setup can't isolate either the low or high pressure side, which can impair low-end performance. GM's new two-stage turbocharger setup looks to eliminate this by linking the high-pressure turbo to the exhaust manifold through the high-pressure inlet duct. The low-pressure turbo is attached to the high-pressure turbo by a low-pressure inlet duct, which is linked to a connecting channel. A single actuator that is housed in the exhaust manifold creates a bypass that can opens the high-pressure inlet or close the connecting channel. Depending on what the engine load and speed is, the ECU guides the actuator—a single rotating spindle with discs corresponding to flanges on the high and low pressure sides—to isolate one of the two turbos. Isolating the turbos allow the respective inlets to be engineered for the best possible fluid dynamic performance. The setup should increase performance and decrease lag. There's no word on what car this setup will make an appearance on, but it will most likely be used in premium vehicles before trickling down to the rest of GM's vehicles. Related Video: News Source: GM Inside News, AutoGuide via GM Authority Cadillac Chevrolet GM Technology Sedan turbo patent engine turbocharging