2012 Chevy Cruze Blue Topaz Metallic Ls 4cyl Automatic All Power Local 1 Owner on 2040-cars
Little Rock, Arkansas, United States
Vehicle Title:Clear
For Sale By:Dealer
Engine:1.8L 1796CC 110Cu. In. l4 GAS DOHC Naturally Aspirated
Body Type:Sedan
Fuel Type:GAS
Interior Color: Black
Make: Chevrolet
Model: Cruze
Trim: LS Sedan 4-Door
Number of Doors: 4
Drive Type: FWD
Drivetrain: Front Wheel Drive
Mileage: 5,230
Sub Model: LS
Number of Cylinders: 4
Exterior Color: Blue
Chevrolet Cruze for Sale
2013 new champagne silver metallic 6spd manual cloth!!! call us today!!!(US $15,995.00)
2012 chevrolet cruze 2ls damaged clean title runs! economical priced to sell!!(US $8,900.00)
2013 cruze 2lt loaded car 10 miles salvage title no reserve
2012 cruze ltz sun roof leather rs pkg hard loaded(US $17,495.00)
2012 chevrolet cruze; mint condition!!
2013 chevrolet cruze 2 lt w/ heated leather seats, sunroof, and mylink pandora(US $19,795.00)
Auto Services in Arkansas
West End Garage Inc ★★★★★
VIP Auto Body & Collision ★★★★★
Ultimate Auto Sales ★★★★★
Trans Tech ★★★★★
Russell`s Truck Accessories ★★★★★
Performance Cars & Trucks ★★★★★
Auto blog
GM to squeeze out more production capacity for midsize trucks
Tue, May 26 2015General Motors was predicting a strong showing for the Chevrolet Colorado and GMC Canyon before they debuted, and demand among dealers for the midsize trucks even exceeded company's expectations. The positive situation has left GM with a problem, though: finding ways to increase capacity for the pickups at the Wentzville Assembly plant in Missiouri. With a third shift already running, GM has continued to look for ways to build just a few more of the trucks at the plant. The company has plans to hire as many as 1,000 more workers for the Saturday and Sunday shifts to construct an additional 2,000 pickups a month, according to unnamed insiders at the factory speaking to Automotive News. The little adjustments even extend to getting rid of an unpaid break to add 18 minute of assembly time over the course of a day, which equals about 3,500 more vehicles a year. All of this effort comes because the trucks are in such high demand. According to GM's figures, the company has delivered a combined 35,720 units of the Colorado and Canyon from January through April 2015, and the Chevy was the fastest-selling truck in the US for the previous three months. In May, it spent an average of just 12 days in showrooms before being snapped up. And even better for the company, 43 percent of these buyers came from other brands. According to Automotive News, the most popular trade-ins have included the Ford F-150, Toyota Tacoma, and Dodge Dakota. Related Video:
Next-gen Chevy Silverado and GMC Sierra may use carbon fiber
Thu, Dec 7 2017It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck
Autoblog Podcast #384
Tue, Jun 10 2014Episode #384 of the Autoblog podcast is here, and this week, Dan Roth, Steven Ewing and Chris Paukert talk about rumors that the Subaru WRX Concept styling may influence the next production model, the 2015 Chevrolet Corvette Z06, and Chris' time with the 2015 Lincoln MKC. We start with what's in the garage and finish up with some of your questions, and for those of you who hung with us live on our UStream channel, thanks for taking the time. Check out the new rundown below with times for topics, and you can follow along down below with our Q&A. Thanks for listening! Autoblog Podcast #384: Topics: Long-term 2015 Subaru WRX introduction Subaru WRX Concept styling may see production 2015 Lincoln MKC 2015 Chevrolet Corvette Z06 In the Autoblog Garage: 2014 Mercedes-Benz E550 Cabriolet 2014 Volkswagen Jetta SEL 2014 Chevrolet Corvette Stingray Hosts: Dan Roth, Steven Ewing, Chris Paukert Runtime: 01:34:21 Rundown: Intro and Garage - 00:00 Long-term WRX intro - 27:20 WRX Concept - 37:10 Lincoln MKC - 47:49 Corvette Z06 - 01:07:18 Q&A - 01:16:18 Get the podcast: [UStream] Listen live on Mondays at 10 PM Eastern at UStream [iTunes] Subscribe to the Autoblog Podcast in iTunes [RSS] Add the Autoblog Podcast feed to your RSS aggregator [MP3] Download the MP3 directly Feedback: Email: Podcast at Autoblog dot com Review the show in iTunes Podcasts Rumormill Chevrolet Lincoln Mercedes-Benz Subaru subaru wrx concept