Chevrolet: Corvette Z06 on 2040-cars

Auto blog

GM finds steering flaw, decides it doesn't warrant a recall

Guess what? General Motors is back in the spotlight for not recalling something. This time, though, not only does the company have an argument against a recall campaign, but its position is supported by the National Highway Traffic Safety Administration. According to The New York Times, over 50 owners of GM vehicles have reported instances of stuck or seized steering after driving long distances without moving the wheel. One owner complained to NHTSA that the "locked" steering of their 2013 Buick Verano caused a collision with a concrete barrier in a construction zone. Along with the 2013 to 2014 model year Verano sedans, Chevrolet Cruze and Malibu sedans are also affected. Considering the popularity of those models, GM needs to have a reason for not issuing a recall, right? "Based on a very low rate of occurrence – ranging from less than one half to less than two incidents per thousand vehicles – and the fact that the condition is remedied when the wheel is turned, GM determined this was not a safety issue," spokesman Alan Adler told The Times. The company has, however, issued a technical service bulletin for owners that complain of the problem. The fix is nothing more than a software update that is covered for 10 years or 150,000 miles from new. NHTSA cited GM's actions, along with descriptions of the problems from customers, in its decision not to issue a recall, with spokeswoman Catherine Howden saying, "the symptoms described would be a brief, perceptible change in steering feel that has little to no effect on the driver's ability to safely steer the vehicle." "When terms like 'notchy,' 'stick,' 'slip' or 'feel' are used, it does not indicate a meaningful increase in steering effort," Howden told The Times via email. What do you think? Is GM in the wrong here? Should there be a recall, or is the issue so limited as to not warrant one? Have your say in Comments. Featured Gallery 2013 Buick Verano Turbo: Review View 20 Photos Related Gallery 2014 Chevrolet Malibu: First Drive View 36 Photos Related Gallery 2014 Chevrolet Cruze Turbo Diesel: Quick Spin View 14 Photos News Source: The New York TimesImage Credit: Copyright 2015 Steven J. Ewing, Seyth Miersma / AOL Government/Legal Recalls Buick Chevrolet GM Safety Sedan buick verano

Chevy might've pulled out of NASCAR if it weren't for new Gen 6 car

We've been on the fence with NASCAR for some time now. On one hand, it's some of the closest racing anywhere in motorsports, with actual passing and door-handle-to-door-handle action as a matter of course. But on the other, it's become template racing - a personality-driven sport more about the drivers than any sort of loyalty to a particular automaker. The Car Of Tomorrow format really rammed that message home, with a racecar's identity coming down to little more than headlamp stickers slapped on the nose. That's not necessarily a bad thing in and of itself, but we've wondered for some time what's in it for the automakers, who pay big money to stay in a series that has had little increasingly little do with street car sales, let alone innovation.
Apparently General Motors was beginning to wonder the same thing. In a new ESPN report, Rick Hendrick, team owner of Hendrick Motorsports, suggests that GM would have seriously considered leaving NASCAR if it wasn't for the move away from the COT to the new Gen 6 racer. According to Hendrick, GM North America boss Mark Reuss spearheaded the charge away from the 2007 COT and toward a racecar with clearer automaker ties - cars like the new Chevrolet SS racer shown above. Learn more about the fight for a closer-to-production look in the ESPN story at the link.
Now, if we could just get more rear-wheel drive V8 coupes into showrooms....

Chevy's 6.6-liter Duramax is pretty much all new

To say there's a heated battle in heavy-duty pickups is an understatement, with Chevrolet, Ford, and Ram constantly trading blows of increased torque, horsepower, and towing capacity. The latest salvo is the revised, more powerful turbo diesel 6.6-liter Duramax V8 in the 2017 Chevy Silverado. It has 910 pound-feet of torque, an increase of 145, putting it nearly level with the Ford Super Duty. Here's a closer look at where those gains come from. How exactly did Chevrolet add all that torque plus 48 horsepower? The automaker essentially took a fine-tooth comb to the entire engine. Chevy says it changed 90 percent of the V8, and the cumulative effect of those small changes adds up to big increases. As you might guess, the turbocharger is updated. The larger unit features electric actuation of the variable nozzle turbine (VNT), and what Chevy calls a double axle cartridge mechanism that separates the VNT moving parts from the housing. That helps with heat performance as well, with a claim that the exhaust side of the turbo can run continuously up to 1,436 degrees Fahrenheit. Helping that cause are six exhaust gaskets made of Inconel - an nickel alloy that contains chromium and iron – and upgraded stainless steel for the exhaust manifold. Despite having the same cast iron cylinder block, albeit with some minor enhancements, the engine has new cylinder heads, pistons, piston pins, connecting rods, and crankshaft, which have all been upgraded to handle 20 percent higher cylinder pressures. Alongside the increase in pressure, Chevrolet also increased the cylinder head's structure with a honeycomb design. The pattern features high-strength aluminum with dual layer water jackets that not only improve strength, but also optimize water flow for better cooling. For 2017, the cylinder head also benefits from integrated plenum that aids the engine in getting more air under heavy loads. The cylinder head isn't the only component to get a minor update, as the pistons have a larger diameter pin for improved oil flow. The same detailed improvements has been bestowed to the humble connecting rods (second in our hearts only to the inanimate carbon rod). The new design has the bolts oriented roughly 45-degrees to the rod instead of parallel. The angle split design, as it's called allows for easier passage through the cylinder.