1989 Chevrolet Corvette 2dr Coupe Hatchback on 2040-cars

Auto blog

Experimental mid-engine XP-819 Corvette going up for auction

It seems to be commonplace that when a new Corvette is in development, rumors swirl about a possible mid-engine layout. As is the case of Chevy's most recent C7 Corvette, these rumors never pan out.
In any case, the idea for a 'Vette with an engine mounted behind the driver can probably all be traced back to a single car, the 1964 XP-819 prototype. Built as an "engineering exercise" back in 1964, the prototype was designed with a rear-mounted engine. History tells us that the idea of a rear-engine Corvette fizzled, and the XP-819 was eventually cut up into pieces and stored at a shop in Daytona Beach, FL.
After sitting for untold years, a restoration project started on the car, and while it isn't yet fully completed, the current owner of the car, Mid America Motorworks, will have the car on display at the 2013 Amelia Island Concours d'Elegance as a "driveable chassis" with hopes of having a fully completed car ready to bring to next year's show.

The Tesla Model S was the best-selling EV of 2015

According to numbers crunched over at Hybrid Cars, the Tesla Model S was the best selling pure electric vehicle last year with 50,366 deliveries. These numbers might not tell the whole story, since Tesla reports deliveries made in 2015 that might have been sold in a different calendar year, while other makers are tallying sales. However, it's inarguable that the Model S ended up in more worldwide driveways than the second-place Nissan Leaf, which did about 43,000 sales. In the US alone, Leaf sales were down 42.8 percent year-on-year, from 30,200 in 2014 to 17,269 last year, and that decline also increased throughout the year. That marks a great finish to a great start to 2015, when Tesla took the lead in EV sales in the US for the first quarter. On top of that, as of last year the Model S becomes the second-best selling EV ever, with 107,148 deliveries since the middle of 2012. It trails the Nissan Leaf, with well over 200,000 worldwide sales. The Chevrolet Volt/Opel Ampera combo takes a close third, with about 106,000 sales. The Nissan and Chevy rivals both launched at the end of 2010, a 16-month head start on the Tesla. Down the charts, the Mitsubishi Outlander PHEV which continues to be forbidden fruit for our market notched 39,000 sales. The BYD Qin PHEV sold 31,898 examples in China, and BYD would take the overall victory from Tesla with 58,728 deliveries if you counted all of its EV and PHEV production, such as its electric buses. The BMW i3 nabbed fourth place with 24,057 global sales. In 2011 the Munich automaker said it wanted to sell 30,000 i3s annually by 2014, but by the time the car launched the company considered 15,000 annual sales 'great for now,' so the 2015 number seems a fine place to wind up. Related Video: News Source: Hybrid Cars Green BMW Chevrolet Mitsubishi Nissan Tesla

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck