1981chevrolet Corvette Convertible on 2040-cars

Auto blog

Driving Granatelli's turbine-powered 1978 Chevy Corvette [w/video]

With its curvy snout and feminine haunches, the third-gen Chevrolet Corvette looks like a dreamy – if dated – exemplar of Sports Car Fantasy 101 when viewed through modern eyes. This particular specimen circa '78, clad in silver and black paint with red pinstripes, appears to be a well-preserved example from the era. Apart from its low-profile Pirellis, slightly raised and slotted hood, spacious stance and a certain hand-painted descriptor alongside its crossed flag logos, you'd never guess there's a Space-Age propulsion unit powering this Coke bottle-bodied ride. Climb inside, and you're presented with aircraft gauges and big, colorful square buttons in the center panel. It takes a push of the "Ignitor" button, a tap of the starter button, and a slide of a T-handle for this nearly 40-year-old sports car to start sounding like Gulfstream G650 ready for takeoff. Yep, you're sitting in an 880-horsepower, turbine-powered Corvette, the only one of its kind in the world. Welcome to the whoosh. What The...? Built by Vince Granatelli, son of Indy 500 guru Andy Granatelli, this curious Corvette came into being by cramming a Pratt & Whitney ST6N-74 gas turbine engine into the donor car's lengthy front end. The same type of Jet A-burning mill powered Granatelli Senior's STP-sponsored racecar at the 1967 Indianapolis 500, where it famously led most of the 198 of 200 laps until a $6 transmission bearing failed, knocking it out of the race. The idea of turbine power usurping internal combustion was so threatening that Indy's governing body restricted turbine performance into obsolescence thereafter. A turbine-powered Corvette sounds excessive because it is. But there are also things about this 880-horsepower, 1,161-pound-feet monster that might surprise you. While it smacks of futurist exoticism and cost a then-dizzying $37,000 in 1967, the Canadian-built powerplant uses 80 percent fewer parts than an internal combustion V8 and will run on virtually anything combustible – whiskey, diesel, even Chanel No. 5. Though it's triple the length of a V8, the Pratt & Whitney beast weighs only 285 pounds. It's also one hell of a robust workhorse, typically serving as an auxiliary power unit for commercial aircraft or a generator in oil fields, where it can run for tens of thousands of consecutive hours before needing an overhaul. To adapt the Chevrolet for jet duty, the nose section was gutted and a sub-frame was built to compensate for the loosey-goosey front end.

2013 Chevy COPO Camaro announced with two new engines and manual option

Chevrolet is following up the 2012 COPO Camaro with another limited run of the drag-strip-ready production car for 2013. Ditching the superchargers, the 2013 COPO Camaro can only be equipped with one of three naturally aspirated V8 engines, and other new features include the option of a manual transmission, new front springs, some minor styling changes and a lower starting price of $86,000. All cars are designed to abide by the rules of the NHRA's Stock Eliminator or Super Stock classifications, depending on in which series buyers wish to enter their Chevrolet Camaro.
Returning for 2013 is the 427-cubic-inch V8 producing 425 horsepower, but the new engines include a 325-hp 350-CID V8 and a 375-hp 396-CID V8. Buyers can select to purchase all three engines, and each will be matched with the sequence number of that car; the track-only COPO cars will not have vehicle identification numbers and can't be registered for street use.
Chevrolet is also offering unique enthusiast-specific options such as a COPO Build Book and the opportunity for owners to help assemble their car's engine at the Chevrolet Performance Build Center in Wixom, MI.

Meet the mother-daughter team that's worked on almost every Chevy Volt

It's Mother's Day, and we're soft enough we love our mothers enough to share a new video from General Motors with you. In it, we meet Monique Watson (left) and Evetta Osbourne, a mother-daughter team that works at the Detroit-Hamtramck Assembly where GM makes the Chevy Volt (along with all of GM's other plug-in hybrids: the Opel Ampera, Holden Volt and Cadillac ELR). The two work side-by-side and have installed the lithium-ion battery pack on almost all of those vehicles - nearly 80,000 of them - since GM started making the pre-production Volts in 2009. In a prepared statement, Watson said that she likes working next to her mom, day in and day out, and they the two are totally in sync when it comes to putting the 400-pound, 16.5-kWh packs into the vehicle undersides. They two can also share stories throughout the day, and Watson said, "The arrangement has absolutely improved our relationship." Osborne started working at Detroit-Hamtramck in 1999, Watson since 2006. If you're driving a Volt today, you probably have them to thank for doing a bit of the work putting your car together. See a short video of them in action below. It's Always Mother's Day for Detroit-Hamtramck Duo Mother, daughter install lithium-ion battery pack in nearly all GM electric vehicles 2014-05-08 DETROIT – For Detroit resident Evetta Osborne, every day is Mother's Day. That's because she literally works side by side with her daughter, Monique Watson, at General Motors' Detroit-Hamtramck assembly plant. They have installed the lithium-ion battery pack on nearly every Chevrolet Volt, Opel Ampera, Holden Volt, and Cadillac ELR since production began. In fact, apart from vacation days and an occasional sick day, the mother-daughter duo has installed almost every battery pack since the Volt was in pre-production in 2009. The ELR launched earlier this year. All told – including Ampera – that's more than 80,000 electric vehicles. "We're a good team and our relationship is secondary when it comes to performing our jobs – but it's great to work alongside my daughter, said Osborne, a mother of five. Because the battery packs weigh more than 400 pounds each, automatic guided vehicles – robotic carts that use sensors to follow a path through the plant – deliver them just as the vehicle body structures glide into position overhead. The carts then lift the T-shaped packs, and Osborne and Watson guide them into the chassis and secure each one with 24 fasteners.