08 Vette, Velocity Yellow W/ebony/cashmere, 3lt, Nav, Ca Car, Chrome Wheels on 2040-cars

Auto blog

10 of 18 midsize SUVs earn 'good' IIHS side impact safety rating

It's not terribly surprising that midsize SUVs earned better safety ratings than small SUVs in the latest side-impact tests performed by the Insurance Institute for Highway Safety (IIHS). Just how much better they scored, on the other hand, certainly raises an eyebrow. Ten out of 18 midsize SUVs earned the highest rating of 'good' in the stringent new test, altered for vehicles starting with the 2020 model year with a heavier barrier (4,200 pounds) that moves at a higher speed (37 miles per hour) and is fitted with a hard honeycomb frontal structure. By way of contrast, just one out of of 20 small SUVs earned a 'good' score.  SUVs that receiving 'good' scores were the Ford Explorer, Infiniti QX60, Lincoln Aviator, Mazda CX-9, Nissan Pathfinder, Subaru Ascent, Toyota Highlander, Volkswagen Atlas, Volkswagen Atlas Cross Sport and Volkswagen ID.4. For EV fans, it's worth noting the ID.4 was the only electric vehicle included in the test. The Buick Enclave and Chevrolet Traverse scraped away with 'acceptable' ratings while the Honda Passport, Honda Pilot, Hyundai Palisade, Jeep Wrangler 4-door, Kia Telluride and Nissan Murano were deemed merely 'marginal' in the tough new test. Only two models — the Mazda CX-9 and Volkswagen ID.4 — earned a "Good" rating in every test category.  Interestingly, the Jeep Wrangler would have scored a 'good' rating if it were equipped with side airbags for the rear seating positions. It would likely be an engineering challenge to equip its removable top and/or doors with airbags, but the lack of that safety feature allowed the head of the rear passenger dummy to hit the vertical support of the top. Otherwise, the Wrangler scored good ratings across the board. The new Ford Bronco, which makes more allowances for side-impact safety, has not yet been tested.  The popular Hyundai Palisade and Kia Telluride SUVs stand out in the test with 'poor' ratings for driver pelvis injuries. The Nissan Murano, a vehicle last redesigned for the 2015 model year, was the only vehicle tested that received a 'poor' rating for its structure and safety cage. Videos of the tests of 12 of these 18 SUVs can be found on the IIHS' YouTube page. Related video: Green Buick Chevrolet Ford Honda Hyundai Infiniti Jeep Kia Mazda Nissan Subaru Toyota Volkswagen Safety Crossover SUV IIHS Insurance Institute for Highway Safety

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck

Our favorite mid-engine Corvette theories and rumors

The mid-engine Corvette! We just saw blurry photos through the foliage, and are hearts are all aflutter because it means that this car is real. And it's the most " never before" Corvette since 1984. Which leads us to all kinds of wacky theories and speculation. Everybody knows something or heard from a guy. None of those guys (or gals) from GM are talking to Autoblog, to be clear. But that won't stop us from stirring the pot. Let's go over a few point-by-point. The pushrod engine will be replaced by an overhead-cam V8 Car and Driver has repeatedly reported that an overhead-cam engine will come after the mid-engine Corvette's debut with an old-school pushrod. We've heard the same thing firsthand, albeit from a source with no connection to the development of the Corvette or powertrain. "At some point two valves can't pass future emissions regulations," said the guy we know. While the pushrod engine is compact, the design makes it difficult - if not impossible - for sophisticated variable valve timing (and lift) systems that control combustion with more precision. Hasty conclusion: The pushrod engine has a finite life in front of it. This one's a lock, it's a just a matter of when. Bowling Green's new paint shop is really the mid-engine assembly line Credit to Reddit for this one. Like we said, everybody knows a guy. But let's look deeper. The new paint facility costs $439 million dollars and adds 450,000 square feet, almost half the size of the existing plant. Plus GM announced another $290 million in upgrades at Bowling Green Assembly. That sure sounds like a lot of money, but you can actually spend that much on a paint booth. Porsche spent 500 million Euros (about $561 million dollars) to add the Macan assembly to its Leipzig, Germany plant in 2014. Chrysler shelled out $850 million for a paint shop in Sterling Heights, Michigan. GM spent $600 million for a new paint shop at the Fairfax (Kansas City) plant. Honda, on the other hand, is working on a thrifty $210 million project in Marysville, Ohio that includes a 300,000 square foot expansion, and the low-volume Acura NSX facility only cost $70 million. Hasty conclusion: The square footage and cost could easily mean a new assembly line instead of (or in addition to) a paint line. And if the NSX plant was really that cheap, GM could have hidden a similar sum in its existing announcements.