Cevy Colorado (no Reserve) Low Miles on 2040-cars
Las Vegas, Nevada, United States
Body Type:TRUCK
Engine:DOHC VVT I-4
Vehicle Title:Clear
For Sale By:Dealer
Interior Color: Gray
Make: Chevrolet
Model: Colorado
Warranty: Dealer Warranty
Mileage: 25,970
Sub Model: LS
Exterior Color: White
Chevrolet Colorado for Sale
- 2005 chevrolet colorado z71 2wd extended cab**trailer pack**3.5 liter**(US $12,990.00)
- 2005 chevrolet colorado 4x4 warranty guaranteed credit approval well maintained
- Florida 75k colorado ls z85 reg cab 5 speed manual alloys super clean
- 2011 chevrolet colorado 4wd crew cab lt - leather - 1 owner - 20k miles(US $22,900.00)
- 2006(06) chevrolet colorado work truck w/ tool box! beautiful white! save big!!!(US $8,995.00)
- 2012 chevy colorado show room condition
Auto Services in Nevada
Welge Automotive ★★★★★
Transmission Specialists ★★★★★
Scorpion Motorsports ★★★★★
Ramirez Windshields And Glass ★★★★★
Preferred Auto Care ★★★★★
Pick-n-Pull ★★★★★
Auto blog
Next-gen Chevy Silverado and GMC Sierra may use carbon fiber
Thu, Dec 7 2017It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck
GM execs fired over fraudulent India emissions testing
Mon, 29 Jul 2013General Motors hadn't had a recall in India since 1995. That changed when it was discovered that certain employees were playing tricks with local emissions testing in order to ensure passing grades for engines. More than ten GM Powertrain employees in India and the US have been let go over the ensuing emissions flap, including Sam Winegarden, VP of global engine engineering, a man who has been with the company since 1969, leading development of some marquee powerplants.
According to Automotive News, an internal investigation revealed that employees "violated testing procedures," sometimes swapping specially prepared low-emissions engines during testing regimes for the Chevrolet Tavera SUV equipped with the 2.0-liter and 2.5-liter engines. Employees were also manipulating weights in order to get vehicles placed into different emissions categories. The discovery has led to GM recall the 114,000 Taveras produced over an eight-year period and halting their production and sale.
The Economic Times of India reports that the issue is due to "a faulty component." GM has developed a solution to the issue, and once it is validated in testing and approved by the Indian authorities, the recalled vehicles will be fixed at dealers and production will resume.
Why does the Corvette Stingray have so many vents? Here's why
Sun, 27 Jan 2013Just looking at the new 2014 Chevrolet Corvette Stingray, it's not hard to see that the car's design was created with aerodynamics at the forefront, but Chevrolet designers point out exactly what went into designing the iconic coupe in a pair of recently released videos. The videos show the Corvette going through early design phases, including clay models and wind tunnel tests, as well as talking to the car's chief engineer, Tadge Juechter.
Both videos help explain various aspects of the C7 Corvette, but it's the aero tuning of the car that is most interesting. This includes extra attention paid to the lower air dam and vented hood to help reduce drag and lift, while the rear quarter inlets are for differential and transmission cooling. Juechter said that some of these aero-tuned elements were inspired from GM's involvement in racing.
If you have about five minutes and you can't get enough information about the new 'Vette, then check out the videos posted below.