1972 Chevelle Ss on 2040-cars

Auto blog

GM announces 3 new recalls affecting 1.7M vehicles in North America [w/video]

Still embroiled in the ongoing ignition switch recall, General Motors announced today three more discrete recalls, affecting a grand total of 1,546,900 vehicles in the US. The Detroit News reports that some 1.7 million vehicles are affected overall in North America. The first and largest of the trio of new recalls concerns some 1.18-million Buick Enclave and GMC Acadia crossovers from the 2008-2013 model years, Chevrolet Traverse from 2009-2013 (pictured above) and Saturn Outlook vehicles from 2008-2010. All of the crossover utilities may have an issue with the wiring harness for their seat-mounted side airbags. Apparently, the vehicles are equipped with a Service Air Bag warning light that, if ignored, "will eventually result in the non-deployment of the side impact restraints." Those restraints include the side airbags, a front-center airbag if the vehicle is so equipped and seatbelt pretensioners. Dealers of affected vehicles will be instructed to remove driver and passenger side airbag wiring harness connectors, and then "splice and solder the wires together." The second recall affects 303,000 Chevrolet Express (pictured right) and GMC Savana vans from model years 2009-2014, and with gross vehicle weights under 10,000 pounds. Said vehicles do not comply with a head impact requirement for unrestrained occupants, and will need a reworking of the instrument panel material to be sent back on the road. It doesn't sound as though there's a quick fix for this one, as the GM press release states: "Unsold vehicles have been placed on a stop delivery until development of the solution has been completed and parts are available." Finally, the third recall affects 63,900 Cadillac XTS luxury sedans from model years 2013 and 2014. A brake booster pump may be susceptible to corrosion by way of the relay, potentially causing and electrical short, overheating, melting of plastic components and even engine fires. GM says it is aware of two engine fires in unsold XTS models and two cases of melted parts. Repairs for the issues affecting the XTS have not not mentioned by GM in the release. The Detroit News is also reporting that along with news of the triple-recall, GM is taking a $300-million credit to help pay for the repair costs, and to deal with the ongoing costs associated with the ignition switch recall. In an attempt to explain just what GM has been doing in the face of these very serious issues, newly minted CEO Mary Barra has addressed the issues in a new video.

Common Dodge Ram 1500 vs. Chevrolet Silverado breakdowns

These two trucks are famous for their ability to get the job done. Still, even the toughest vehicle can have mechanical problems at some time. What if we match the Dodge Ram 1500 and Chevrolet Silverado head to head? Let's find out more about common repairs for each model. Also, learn some tricks to pay for car repairs. Clunky Steering Both Dodge and the Chevy owners sometimes notice bumping and clunking when steering. This might be more noticeable when driving over bumps. The cause is usually different in each truck though. In the Dodge Ram, clunky steering is more likely due to a defective lower ball joint. Replacement costs around $300 - $400, parts and labor. Clunky Chevy Silverado steering is probably a steering rack failure. This problem appears more often in trucks with over 90,000 miles. Silverado steering rack repair will run you up to $1,000 or more. Starting Woes For the Chevy Silverado with over 130,000 miles, you might notice trouble starting. This problem may appear occasionally at first, but it typically gets worse. Excluding a weak battery, the culprit is usually the starter. Replacement will cost you around $330 - $500. Of the total cost, $90 is for labor only. Now the Dodge Ram might make a ticking sound when starting, especially on models with over 94,500 miles. The noise often disappears after the engine warms up. These symptoms may indicate a broken exhaust manifold. Repair costs range from $800 - $900. Burning Oil & Gas Gauge On The Blink Sometimes, the Dodge Ram burns oil much faster than normal. In models with over 125,000 miles, this often points towards a leaky intake manifold gasket. A knocking sound may also appear with acceleration along with possible engine misfire. The cost to repair is around $200 - $300. The Chevy Silverado has its own surprises, especially when you've filled the gas tank but the gauge still reads low. Or the needle fluctuates widely from low to full while driving. In trucks with over 120,000 miles, it's likely due to a faulty fuel sensor. You might need a full fuel pump replacement, which can cost you up to $820, parts and labor. Water Inside And Poor Heat The Ram 1500 rear window has been known to leak. You might notice the back seat and floor wet after a rainstorm. This is more common in trucks with over 65,000 miles. Resealing the Ram 1500 rear window costs around $150 - $250.

Pure Vision Design TT Camaro has 1,400 reasons to want it

We've talked about Pure Vision Design before, a California-based company that made waves at last year's SEMA show with its Martini-liveried, Indy-car-powered Ford Mustang. That same car later starred in a Petrolicious video we showed you just a few weeks back. The company's latest creation is a menacing car it calls the Pure Vision Design TT Camaro. Based on a 1972 model, this car shares the Martini Mustang's clean styling and obsession with details.
Unlike the Mustang, which draws its power from a mid-60s Lotus-Ford Indycar engine, the "TT" in this Camaro's name implies something far more potent. The Nelson Racing Engines 427-cubic-inch V8 has been fitted with a pair of turbochargers, with a claimed output of 1,400 horsepower. That's almost 1,000 more than the Martini Mustang.
A six-speed Magnum transmission dispatches that power to the ground, while Pirelli PZero tires are tasked with (somehow) trying to grip the road. Baer brakes hide behind those HRE rims, while JRI coilovers and HyperTech springs bless the Camaro with some degree of competency in the bends.