1971 Chevelle Ss Big Block 454 Restored on 2040-cars

Auto blog

NHTSA investigating nearly 750,000 GM models over non-deploying airbags

Nearly 750,000 vehicles built by Chevrolet, GMC, and Cadillac are the subject of a National Highway Traffic Safety Administration (NHTSA) investigation due to non-deploying driver-side airbags. While the investigation is ongoing, the agency believes the issue is likely due to rust particles that form on the inflator's connection terminal interface. The list of nameplates included in the investigation includes Chevrolet's Silverado, Tahoe, and Suburban, GMC's Sierra, Yukon, and Yukon XL, plus Cadillac's Escalade, Escalade ESV, CT4, CT5, and XT4. All of the potentially affected vehicles are 2020 or 2021 models, according to a bulletin published on the NHTSA's website. Investigators launched the probe in April 2021 after 15 consumers reported airbag-related issues, including nine who said an airbag malfunction light appeared in the instrument cluster. More alarmingly, the NHTSA is aware of six accidents that caused significant damage to the car's front end yet didn't trigger the driver's airbag. It adds that there are no fatalities linked to the issue, but there are six crashes and eight injuries reportedly blamed on it. No evidence suggests this problem is related to the millions of potentially deadly Takata inflators recalled over the past few years. General Motors is aware of the defect. It sent a technical service bulletin (TSB) to its dealers in March 2021 to address the aforementioned warning light. The note explains the issue is due to "rust particles in the connection terminal interface of the driver's airbag inflator." The company hasn't issued a safety recall yet, however. Whether it will partially depends on the NHTSA's findings. It's currently looking into the scope and the severity of the problem, and it wants to understand its implications on driver safety. Investigators will decide whether General Motors needs to recall the 749,312 cars that are part of the probe when they close their investigation. General Motors has already spent a significant amount of money replacing defective airbag-related parts in its cars. In November 2020, it was ordered by the American government to recall nearly 6 million pickup trucks and SUVs equipped with potentially dangerous Takata airbag inflators. It repeatedly argued that testing proved the inflators were safe, and it petitioned the agency four times starting in 2016 to avoid a recall, which cost an estimated $1.2 billion (about a third of its net income in 2020).

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck

That time we lapped Indy with Tony Kanaan in a Corvette Z06

We're here in Indianapolis, IN, attending this weekend's 99th running of the Indy 500. The big event happens tomorrow, but the city is buzzing today with all sorts of pre-race festivities. For us, that means checking out Indianapolis Motor Speedway a day early, and getting a hot lap around the racetrack in the official Indy 500 pace car – a 2015 Chevrolet Corvette Z06. Our driver for the occasion is IndyCar racer Tony Kanaan, who won the Indianapolis 500 in 2013. Of course, he'll be competing tomorrow, leaving pace duties to none other than Jeff Gordon. Check out our minute-and-a-half-long lap of the Indy 500 track in the video above, where Kanaan hugs the wall in true race style, getting the Z06 past 150 miles per hour on the back straight. Stay tuned for more Indy 500 coverage later this weekend.