1969 Chevrolet Chevelle 383 Stroker on 2040-cars

Auto blog

The USPS needs 180,000 new delivery vehicles, automakers gearing up to bid

Winning the New York City Taxi of Tomorrow tender was a huge prize for Nissan, even though the company is still working through the process of claiming its prize. The United States Postal Service has begun the process to take bids for a new delivery vehicle to replace the all-too-familiar Grumman Long Life Vehicle, and that will be a much larger plum for the automaker who wins it, perhaps worth more than six billion dollars. The Grumman LLV is an aluminum body covering a Chevrolet S-10 pickup chassis and General Motors' Iron Duke four-cylinder engine. The USPS bought them from 1987 to 1994, and the 163,000 of them still in service are a monumental drain on postal resources: they get roughly ten miles to the gallon instead of the quoted 16 mpg, drink up more than $530 million in fuel each year, and their constant repair needs like the balky sliding door and leaky windshields have led the service to increase the annual maintenance budget from $100 million to $500 million. A seat belt is about as modern as it gets for safety technology, and the USPS says that assuming things stay the same, it can't afford to run them beyond 2017. Last year it put out two triage requests for proposals seeking 10,000 new chassis and drivetrains for the Grumman and 10,000 new vehicles. The LLV is also too small for the modern mail system in which package delivery is growing and letter delivery is declining. The service says it doesn't have a fixed idea of the ideal "next-generation delivery vehicles," but it listed a number of requirements in its initial request and is open to any proposal. Carriers have some suggestions, though, saying they want better cupholders, sun visors that they can stuff letters behind, a driver's compartment free of slits that can swallow mail, and a backup camera. The request for information sent to automakers pegs the tender at 180,000 vehicles that would cost between $25,000 and $35,000 apiece, and it will hold a conference on February 18 to answer questions about the contract. GM is the only domestic maker to avow an interest, while Ford and Fiat-Chrysler have remained cagey. Yet with a possible $6.3 billion up for grabs and some new vans for sale that would be advertised on every block in the country, we have a feeling everyone will be listening closely come February 18. We also have a feeling the LeMons series is going to be flooded with Grummans come 2017. News Source: Wall Street Journal, Automotive News - sub.

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck

Chevy shows much-improved 2014 Corvette interior in new video

If you want a closer look at what went into designing and building the interior for the 2014 Chevrolet Corvette, we've got just the thing. General Motors has released a new video detailing the cabin's evolution from conception to execution, complete with commentary from Ryan Vaughn, performance car interior design manager with Chevrolet. The quick clip details how manufacturing, engineering and design within General Motors worked together from the first sketches to ensure no compromises had to be made later down the line. How novel.
With plenty of hides traced with contrast stitching and available real carbon fiber trim, the cabin looks to be a few hundred miles ahead of the C6. Given how readily critics derided the previous generation for its cabin, the C7 should make writers work a little harder to find something to complain about. Check out the video below for yourself.