1969 Chevelle Ss Drag Car on 2040-cars

Auto blog

GM applies for LT5, LTX trademarks... are new small block variants coming?

Recently discovered General Motors trademark applications for LT4, LT5, LT88 and LTX have observers wondering what kind of high-performance offerings could be on their way. A new LT4 would mark a return of the engine designation first used on the Corvette Grand Sport, SLP Pontiac Firehawk and SLP Chevrolet Camaro SS from 1996 and 1997. Supposition at Corvette Forum - which provided advance intel on the C7 like these leaked images - believes a new LT4 could go into the high-performance trim of the next-gen, 2015 Camaro that would be more powerful than the 580-horsepower Camaro ZL1.
Seeing an LT5 again would also be déjà vu - in its former life it was a 5.7-liter V8 for the C4 Corvette ZR-1 from 1990-1994 designed by Lotus, producing from 370 hp to 405 hp. A mix of rumor and hope is that the new LT5 will be a supercharged evolution of the 6.2-liter LT1 (pictured) placed in the new C7 Corvette, and that it will go into the C7 version of the ZR1 pumping out something like 700 hp.
The LTX trademark is, as with that last letter, a complete mystery. If the "X" isn't a generic way to denote the whole LT family, it's wondered if it LTX could refer to a crate motor offering like the LSX.

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck

Chevy SS prototype spotted wearing Pontiac G8 clothes

Do not adjust your computer screen, you are not seeing the rebirth of the Pontiac brand. General Motors has chosen to use a G8 to disguise a test mule for the latest prototype of the forthcoming Chevrolet SS. The G8 was closely related to the Holden Commodore and Vauxhall VXR, the platform upon which the new Chevrolet performance model will be based. It should come as little surprise, then, that GM has opted to use the cladding from the former G8.
Thought the front clip of this mule is pure Pontiac, note the vents immediately behind the front wheel. That is a distinctive design hallmark of the Vauxhall VXR. Also note that this vehicle is right-hand drive, as the Holden and its Chevy counterpart will be very closely related. That likely includes potential drivetrains. The spy photos of this mule also reveal very wide rear tires, and rear wheels that do not match the fronts.