1967 Chevrolet Chevelle 396 V8 Th400 Auto Pwr Steering 4 Wheel Pwr Disc Brakes on 2040-cars

Auto blog

Final C6 Corvette built in Bowling Green

With all of the attention given to the 2014 Chevrolet Corvette Stingray lately, you could be forgiven for thinking that it's already well along in production, yet tooling up for the new C7 has only just begun. In fact, production of the outgoing C6 generation in Bowling Green, Kentucky just halted on Thursday.
As the C6 has aged, production numbers have predictably ebbed along with demand, but this year, the addition of the 427 and 60th anniversary models resulted in an uptick in vehicles built - this, despite a model year shortened by around 25 percent to accomodate the new model changeover. The final C6 Corvette ever, No. 13,466 built this year, was a white 427 Convertible destined for the General Motors Heritage Center museum. The car's 7.0-liter V8 heart was assembled by Corvette chief engineer Tadge Juechter himself.
In total, Bowling Green pushed out 215,100 C6 Corvettes over nine years. If you're still a C6 fan at heart and are hoping to get a good deal on a phase-out model, step lively - Chevrolet reportedly had about 6,100 unsold units, which Autoweek suggests is good for around five and a half months of supply at the model's current sales rates. Given that demand will likely slacken even further as the C7 draws closer, that should be a big enough stockpile to keep dealers satisfied until 2014 Stingrays begin showing up on their forecourts in December.

GM recalls Chevy Express, GMC Savana over rollaway concern

The National Highway Traffic Safety Administration has issued a recall notice for a small number of General Motors fullsize vans due to possible rollaway concerns. On certain 2013 Chevrolet Express and 2013 GMC Savana models, it is possible to remove the key from the ignition without the shifter being in park.
Only 980 total units are being affected by this recall, and GM is fixing the issue by replacing the ignition cylinder and associated keys. Affected Chevy vans were built during most of November and December while its GMC counterpart was only built for a week in November. The recall goes into effect on January 23, and to find out if your vehicle applies to the recall, the GM and NHTSA contact numbers can be found on the official recall notice, which is posted below.

GM recalls 3,300 pickups and SUVs for new ignition-switch issue [UPDATE]

UPDATE: A statement from GM about the recall has been added below. The exact total of vehicles affected is 3,296, including 3,073 of them in the US. General Motors isn't letting an ignition-switch problem grow into a massive scandal again. The automaker is recalling about 3,300 North American trucks and SUVs. They are: the 2014 Chevrolet Silverado and GMC Sierra and the 2015 Chevy Suburban and Chevy Tahoe, as well as 2015 model heavy-duty pickups, the Detroit News reports, citing an Associated Press story. The issue appears to have been caught fairly quickly. In this case, the keys can get stuck in the "start" position and then slip to "accessory" if bumped. This is because the ignition lock gears have an outer diameter that's larger than the specifications allow. When that happens the engine shuts off, and the driver loses assistance to the steering and brakes. The airbags might also be affected. The vehicles get a new ignition-lock housing to fix the problem. According to the Detroit News, an employee who experienced the problem with the switch discovered the issue, and this person then let officials at the automaker know as part of the Speak Up for Safety program. A total of five reports of the fault were discovered. However, there are no cases of injuries or crashes. The claims to the automaker's resolution program eventually tallied that GM's previous ignition switch problem included 124 deaths and 275 injuries. The company also had to recall millions of vehicles and pay significant fines to the US government. GM Statement General Motors is recalling 3,073 full-size trucks from the 2014 and 2015 model years in the U.S. Some of these vehicles may have an ignition lock actuator gear with an outer diameter that exceeds specifications, which may make turning the ignition key difficult. The ignition key could get stuck in the "start" position. This may be more likely at higher interior ambient temperatures. If the vehicle is driven with the key stuck in the "start" position, and the vehicle experiences a significant jarring event or the vehicle's interior temperature cools, the ignition lock cylinder could move out of the "start" position, rotate past the "run" position, and move into the "accessory" position, leading to loss of power steering assist, power brakes and potentially air bag deployment in certain crashes. Dealers will replace the ignition lock housing.