2001 Chevy 2500 4x4 Wrecker/tow Truck Repo Towtruck Chevrolet Chase Truck Chaser on 2040-cars

Auto blog

First 2015 Chevy Corvette Z06s en route to owners [w/video]

Pretty much right on schedule, Chevrolet has begun shipping the very first customer examples of its 650-horsepower, supercharged Corvette Z06. In fact, according to General Motors, the earliest Z06s could be in customer hands by the end of this week. "It has been an incredible opportunity to work on Chevy's most capable model," said Jeff Lamarche, manager of Chevy's Bowling Green Assembly plant. "It truly is an amazing car, and we're thrilled to get them into the hands of our eager customers." Prices for the Z06 start at $78,995 for the hardtop model, while the first-ever Z06 Convertible kicks off at $83,995. Take a look below for the official press release from Chevrolet, and while you're down there, we've slipped in a new video of Corvette Racing's Tommy Milner taking a hot lap of Road Atlanta in a Z06, complete with some Performance Data Recorder footage. First 2015 Corvette Z06s on Their Way to Customers Most capable model in Chevrolet's history now shipping from Bowling Green BOWLING GREEN, Ky. – Chevrolet is now shipping the all-new 2015 Corvette Z06 coupe from Bowling Green Assembly and some early customers could receive the much-anticipated supercar later this week. "It has been an incredible opportunity to work on Chevy's most capable model," said Jeff Lamarche, plant manager of General Motors' Bowling Green Assembly plant, "It truly is an amazing car, and we're thrilled to get them into the hands of our eager customers." The new Corvette Z06 offers the most choice for customers in the model's history. It is the first Z06 to offer an available eight-speed paddle-shift automatic transmission and, thanks to a stronger aluminum frame, a removable roof panel. In addition, it is the first time since 1963 that the Z06 is available as a convertible – which will arrive in early 2015. The new LT4 supercharged 6.2L V-8 engine is SAE-certified at 650 horsepower (485 kW) at 6,400 rpm and 650 lb-ft of torque (881 Nm) at 3,600 rpm – making the 2015 Corvette Z06 the most powerful production car ever from General Motors and one of the most powerful production cars available in the United States. To balance performance and efficiency, the LT4 leverages a trio of advanced technologies – direct injection, Active Fuel Management (cylinder deactivation) and continuously variable valve timing –with a new, more efficient supercharger. The LT4 helps make the Corvette Z06 the most capable car in the brand's history.

2016 Camaro gets most revealing tease yet

Chevrolet started its long teaser campaign for the 2016 Camaro by just revealing the exhaust manifold and front frame, but as time has passed the company has slowly unveiled more. In the latest glimpse ahead of the pony car's May 16 debut, we're actually getting to see the model's profile completely undisguised. As suggested by the recent tease of the rear and hood, the 2016 Camaro wears a sharper, more angular design than the current model. This is especially the case when you look at the taut lines making up the rear. Chevy claims that the new shape underwent 350 hours of wind tunnel tests to be able to generate left lift, improve cooling and reduce wind noise in the cabin. A smooth underbody pan is among the aerodynamic tweaks, and it runs from underneath the front grille to the center of the Camaro. Chevy asserts that all of the changes at the front help reduce lift by 30 percent. Related VIdeo: 2016 Camaro is all about the Aero Total aerodynamic lift improved by 30 percent for improved stability 2015-05-11 DETROIT – After 350 hours of wind tunnel testing – often 24 hours a day – the new Camaro will slip more easily through the wind, and drivers of the Camaro SS will experience a marked improvement in reduced aerodynamic lift. These changes illustrate the lengths the aerodynamics team went to for improved performance, stability, cooling and lower wind noise intrusion "The importance of aerodynamics increases exponentially as we increase vehicle performance," said Kirk Bennion, Exterior Design manager. "As engine output increases, we need more engine cooling. As acceleration and top speeds climb, we need to reduce lift for better high-speed stability. However, we cannot make any changes at the expense of increasing drag, which can hurt fuel economy. "To balance these different aerodynamic targets, we tested literally hundreds of changes on the new Camaro, millimeters at a time." For example, the initial design called for the lower grille bars to be set at a 20-degree angle to the horizon. However, after meticulous testing, the team improved engine-cooling airflow by 1 percent by shifting the angle to 13 degrees – a change that achieved the airflow target while maintaining the original grille design. And rather than a traditional front air dam to reduce aerodynamic lift, the team developed a flush belly pan that stretches from the front grille to the center of the vehicle.

Huge, pricey trucks haul jobs and profits for the Detroit Three

DECATUR, Texas — Mickey McMaster is on his 12th pickup truck. The 61-year old farm equipment dealer in Decatur, Texas, two weeks ago treated himself to a 2019 GMC Denali for around $69,000 — a reward for long hours at work. "For me this is the Cadillac of trucks, it's a real luxury vehicle," McMaster said. "I've worked my way up to afford a truck like this and it shows that I've earned it." McMaster is the kind of customer General Motors Co is banking on as it plans to add 1,000 jobs at a plant in Flint, Michigan that will build a new generation of its largest pickups. Demand from Texas and other heartland states for big pick-ups is providing a lifeline to many workers the No. 1 U.S. automaker is laying off at plants elsewhere. The Detroit Three automakers and thousands of their U.S. workers are counting on customers like McMaster to keep buying bigger and more luxurious pickup trucks even if overall U.S. vehicle demand weakens this year, as most analysts predict. At Flint, GM will build a new generation of its heavy-duty Chevrolet Silverado and GMC Sierras, including luxury models that are some of the most profitable vehicles on the planet. GM, Ford Motor Co and Fiat Chrysler Automobiles NV's Ram division own the segment and are each doubling down with new or redesigned models launching this year. Sales of heavy-duty pickups in the United States have grown to more than 600,000 vehicles a year, up more than 20 percent since 2013, according to industry data. Prices for luxury models can easily top $70,000. GM on Tuesday celebrated the launch of a new generation of heavy-duty GMC and Chevrolet pickups at the assembly plant in Flint, Michigan, that is now building all such trucks for the company. At the same time that GM is laying off thousands of U.S. workers and planning to shutter five North American factories, Flint is hiring. The plant runs on three daily shifts, six days a week. As the new model's assembly system ramps up, the plant's capacity will increase by more than 25 percent, plant manager Mike Perez told Reuters. The Flint plant plans to add 1,000 workers, more than half of the 1,500 factory workers who have asked to transfer from plants GM has targeted for shutdown as part of CEO Mary Barra's restructuring plan. "We're bringing in 50 to 100 people every week," said Perez. Workers last week were still finishing the job of retooling the Flint factory to build the new heavy-duty trucks as part of a $1.5 billion investment project.