1992 Chevrolet K2500 Cheyenne Extended Cab Pickup 2-door 5.7l on 2040-cars

Auto blog

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck

First 2015 Chevy Corvette Z06 engine blows up at just 891 miles

You've waited and watched and waited some more for the arrival of your 650-horsepower, $78,000 Chevrolet Corvette Z06. Finally, that joyous day arrives and you eagerly, but gingerly, begin to break-in the 6.2-liter supercharged V8 monster under your hood. Then 900-odd miles after delivery, your excitement grinds, quite literally, to a halt. That's what the owner of one 2015 Z06 claimed happened to him when a simple break-in drive resulted in a lunched engine. The owner, known as Lawdogg149 on Corvette Forum, says he was out breaking-in his car ahead of a January track event when it happened. "While making a pull from 35 miles per hour, I accelerated and shifted short of redline, and boom - the car began knocking. I pulled over and popped the hood. I could hear a loud knock coming from the No. 6 cylinder area along with a serious, grinding, metal-on-metal sound coming from the supercharger area," Lawdogg wrote. A subsequent trip to the dealer confirmed his concerns, with the service facility telling Lawdogg that the No. 6 valvetrain had failed. The dealer couldn't research the issue further, though, as General Motors requested the engine be returned for a more thorough evaluation. The good news for the Z06's unlucky owner, at least, is that GM will be covering the engine replacement under warranty, an expense that Corvette Forum estimates is a nearly $24,000 procedure. At this point, the two leading theories behind the engine's detonation involve a manufacturing defect – which could be why GM is so keen to tear the blown powerplant down – or a mistake on the part of Lawdogg. As Motor Authority points out, such an error could be something as simple as the Z06's owner accidentally shifting to first rather than third during his 35-mph pull. If, however, there's a deeper manufacturing problem with the Z06's engine, this might not be the only case we end up hearing about.

Chevy working on production Impala Midnight Edition

To put together the Impala Blackout concept for SEMA, Chevrolet didn't need to go much further than its accessories catalog. The in-house connection is what could make it possible for Chevy to get a production version of the Blackout into dealers this model year, with its few bits of chrome trim and dark detailing on the 19-inch aluminum wheels set into an abyss of gloss black paint, black Bowtie, grille surround, rear spoiler and mirror caps. The interior is black leather, with stainless steel for the sill plates and pedals, and an 11-speaker Bose audio system, and it gets the optional 305-horsepower, 3.6-liter V6. The brand's marketing director for cars and crossovers, Steve Majoros, told Edmunds that it could come in late spring, and that it will be called "Midnight Edition." Majoros didn't give any indication of pricing or if the production car will be spec'd out like the concept. If you simply don't want to wait for late spring, you could work your DIY mojo by putting one together the same way Chevrolet did: give the accessories catalog a workout. Related Video: