1991 Gmc Sierra 1500 4 X 4 With Meyer Snow Plow on 2040-cars

Auto blog

Driving Granatelli's turbine-powered 1978 Chevy Corvette [w/video]

With its curvy snout and feminine haunches, the third-gen Chevrolet Corvette looks like a dreamy – if dated – exemplar of Sports Car Fantasy 101 when viewed through modern eyes. This particular specimen circa '78, clad in silver and black paint with red pinstripes, appears to be a well-preserved example from the era. Apart from its low-profile Pirellis, slightly raised and slotted hood, spacious stance and a certain hand-painted descriptor alongside its crossed flag logos, you'd never guess there's a Space-Age propulsion unit powering this Coke bottle-bodied ride. Climb inside, and you're presented with aircraft gauges and big, colorful square buttons in the center panel. It takes a push of the "Ignitor" button, a tap of the starter button, and a slide of a T-handle for this nearly 40-year-old sports car to start sounding like Gulfstream G650 ready for takeoff. Yep, you're sitting in an 880-horsepower, turbine-powered Corvette, the only one of its kind in the world. Welcome to the whoosh. What The...? Built by Vince Granatelli, son of Indy 500 guru Andy Granatelli, this curious Corvette came into being by cramming a Pratt & Whitney ST6N-74 gas turbine engine into the donor car's lengthy front end. The same type of Jet A-burning mill powered Granatelli Senior's STP-sponsored racecar at the 1967 Indianapolis 500, where it famously led most of the 198 of 200 laps until a $6 transmission bearing failed, knocking it out of the race. The idea of turbine power usurping internal combustion was so threatening that Indy's governing body restricted turbine performance into obsolescence thereafter. A turbine-powered Corvette sounds excessive because it is. But there are also things about this 880-horsepower, 1,161-pound-feet monster that might surprise you. While it smacks of futurist exoticism and cost a then-dizzying $37,000 in 1967, the Canadian-built powerplant uses 80 percent fewer parts than an internal combustion V8 and will run on virtually anything combustible – whiskey, diesel, even Chanel No. 5. Though it's triple the length of a V8, the Pratt & Whitney beast weighs only 285 pounds. It's also one hell of a robust workhorse, typically serving as an auxiliary power unit for commercial aircraft or a generator in oil fields, where it can run for tens of thousands of consecutive hours before needing an overhaul. To adapt the Chevrolet for jet duty, the nose section was gutted and a sub-frame was built to compensate for the loosey-goosey front end.

Foreign automakers pay from $38 to $65 per hour to non-union workers

As leaders for the United Auto Workers gather in Detroit for their Special Convention on Collective Bargaining to work out the negotiating stance for this year's new labor agreements with the Detroit 3 automakers, what they most want to do is figure out how to eliminate the two-tier wage scale. However, the lower Tier 2 wage has allowed the domestic automakers to reduce their labor costs, hire more workers, and compete better with their import competition. As it stands, per-hour labor rates including benefits are $58 at General Motors, $57 at Ford, and $48 at Fiat-Chrysler – a reflection of FCA's much greater number of Tier 2 workers. The Center for Automotive Research released a study of labor rates (including benefits) that put numbers to what the imports pay: Mercedes-Benz pays the most, at an average of $65 per hour, Volkswagen pays the least, at $38 per hour, and BMW is just a hair above that at $39 per hour. Among the Detroit competitors, Honda workers earn an average of $49 per hour, at Toyota it's $48 per hour, Nissan is $42 per hour, and Hyundai-Kia pays $41 per hour. The lower import wages are aided by their greater use of temporary workers compared to the domestics. Automotive News says the ten-dollar gap between those foreign camakers and the domestics turns out to about an extra $250 per car in labor, which adds up quickly when you're pumping out many millions of cars. That $250-per-car number is one that, come negotiating time, the Detroit 3 will want to reduce, as the UAW is trying to raise both Tier 1 and Tier 2 wages. Another wrinkle is that the domestic carmakers are considering the wide adoption of a third wage level lower than Tier 2. Some workers who do minor tasks like assembling parts trays kits and battery packs already make less than Tier 2, but the UAW will be quite wary about cementing yet another wage scale at the bottom of the system while it's trying to fight a bigger battle at the top. News Source: Automotive News - sub. req., BloombergImage Credit: AP Photo/Erik Schelzig Earnings/Financials UAW/Unions BMW Chevrolet Fiat Ford GM Honda Hyundai Kia Mercedes-Benz Nissan Toyota Volkswagen labor wages collective bargaining labor costs

Chevy Trax engineer says GMC version possible

The Buick Encore is doing so well and its platform-mate the Chevrolet Trax has such good reviewer vibes going for it already, that a GMC version hasn't been ruled out. During the recent press launch, Automotive News asked lead engineer Al Manzor if the Trax could wear a GMC-branded suit, to which Manzor replied, "I think that is certainly possible." That's a long way from telling us anything about the probability of a GMC version of the Trax, and a legion of questions would need to be answered before it could happen. How would a GMC version be priced to leave room for the $26,465 GMC Terrain but not eat into sales of the $20,995 Trax or the $24,035 Encore? Or would that matter? Could it primarily be considered to encourage a new faction of The Yukon Set at the compact end, GMC buyers being famously committed to the marque? And of course, would there be a Denali version? It'll probably be a long while before we have any kind of answers, but if you want to see it happen, the door to your campaign of persuasion is at least ajar.