1985 Chevrolet C/k Pickup 1500 on 2040-cars

Auto blog

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck

GM recalling 70k Chevy Malibus, Pontiac G6s over steering issue

A problem with the power steering system in the Chevy Malibu and Pontiac G6 has prompted General Motors and the National Highway Traffic Safety Administration to issue a recall for an estimated 69,633 vehicles. The issue revolves around the electric power steering assist, which could suddenly fail and increase the risk of a crash, especially at low speeds where the power steering is most helpful. The recall affects 2006-2007 Chevy Malibu sedans and Malibu Maxx wagons (specifically those manufactured between April 1, 2006, and June 30, 2006), as well as the Pontiac G6 (which was offered as a sedan, coupe or convertible) from the same model years and manufactured from April 18, 2006, to June 30, 2006. Owners of the affected units can expect to hear from the manufacturer with instructions to bring in their vehicles to their local dealers to have the torque sensors in the power steering system replaced. RECALL Subject : Sudden Loss of Electric Power Steering , 1 INVESTIGATION(S) Report Receipt Date: FEB 04, 2015 NHTSA Campaign Number: 15V064000 Component(s): STEERING Potential Number of Units Affected: 69,633 Manufacturer: General Motors LLC SUMMARY: General Motors LLC (GM) is recalling certain model year 2006-2007 Chevrolet Malibu and Malibu Maxx vehicles manufactured April 1, 2006, to June 30, 2006, and 2006-2007 Pontiac G6 vehicles manufactured April 18, 2006, to June 30, 2006. In the affected vehicles, there may be a sudden loss of electric power steering (EPS) assist that could occur at any time while driving. CONSEQUENCE: If power steering assist is lost, greater driver effort would be required to steer the vehicle at low speeds, increasing the risk of a crash. REMEDY: GM will notify owners, and dealers will replace the torque sensor assembly, free of charge. The manufacturer has not yet provided a notification schedule. Owners may contact Chevrolet customer service at 1-800-222-1020 or Pontiac customer service at 1-800-762-2737. GM's number for this recall is 14772. Note: This is an expansion of recall 14V-153 to cover additional vehicles built between April 1, 2006 and June 30, 2006. NOTES: Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.safercar.gov.

Pure Vision Design TT Camaro has 1,400 reasons to want it

We've talked about Pure Vision Design before, a California-based company that made waves at last year's SEMA show with its Martini-liveried, Indy-car-powered Ford Mustang. That same car later starred in a Petrolicious video we showed you just a few weeks back. The company's latest creation is a menacing car it calls the Pure Vision Design TT Camaro. Based on a 1972 model, this car shares the Martini Mustang's clean styling and obsession with details.
Unlike the Mustang, which draws its power from a mid-60s Lotus-Ford Indycar engine, the "TT" in this Camaro's name implies something far more potent. The Nelson Racing Engines 427-cubic-inch V8 has been fitted with a pair of turbochargers, with a claimed output of 1,400 horsepower. That's almost 1,000 more than the Martini Mustang.
A six-speed Magnum transmission dispatches that power to the ground, while Pirelli PZero tires are tasked with (somehow) trying to grip the road. Baer brakes hide behind those HRE rims, while JRI coilovers and HyperTech springs bless the Camaro with some degree of competency in the bends.