Chevy C10 Swb on 2040-cars

Auto blog

GM 6.2L V8 claims most powerful light-duty truck engine title

General Motors has officially captured the horsepower crown for mainstream pickup trucks with its 6.2-liter V8. The big mill, available in both the Chevrolet Silverado and GMC Sierra, comes to market with 420 horsepower and 460 pound-feet of torque, handily outdoing its two cross-town competitors, Ram (5.7-liter V8, 395 ponies and 407 lb-ft) and Ford (6.2-liter V8, 411 hp and 434 lb-ft).
The new GM 6.2 will take a bit of an investment, though. Those that want the extra thrust will need to go with either the LTZ or High Country trims from the Chevy, or the SLT and Denali trims from GMC, which are the two highest trim levels for the respective vehicles. Trim levels aside, if you're in the business of towing, GM has you covered. Optioned with the 6.2-liter V8 and the Max Trailering Package, owners will be able to pull 12,000 pounds, a hugely impressive figure.
We still aren't certain as to what sort of economy the new engine will get, but it'll probably be a bad bet for the fuel conscious. As for availability, expect to see the 6.2-liter trucks in showrooms later in the fall.

GM recalls Chevy Express, GMC Savana over rollaway concern

The National Highway Traffic Safety Administration has issued a recall notice for a small number of General Motors fullsize vans due to possible rollaway concerns. On certain 2013 Chevrolet Express and 2013 GMC Savana models, it is possible to remove the key from the ignition without the shifter being in park.
Only 980 total units are being affected by this recall, and GM is fixing the issue by replacing the ignition cylinder and associated keys. Affected Chevy vans were built during most of November and December while its GMC counterpart was only built for a week in November. The recall goes into effect on January 23, and to find out if your vehicle applies to the recall, the GM and NHTSA contact numbers can be found on the official recall notice, which is posted below.

GM patent reveals new two-stage turbocharger

Modern turbochargers may be some of the best ever made, but performance is something that engineers are always trying to improve. According to GM Inside News, General Motors (GM) is hoping to alleviate some of the negative aspects of a two-stage turbocharger setup with a newly-patented design. The patent, that was filed on May 19, 2016, reveals a clever bypass system that allows the engine, a four-cylinder unit, to optimize both the low-pressure and high-pressure inlets for its respective functions. According to the filing, a conventional two-stage turbocharger setup is engineered to allow both turbines to operate simultaneously at low and mid engine speeds. At high engine speeds, only the low-pressure turbine works. The setup can't isolate either the low or high pressure side, which can impair low-end performance. GM's new two-stage turbocharger setup looks to eliminate this by linking the high-pressure turbo to the exhaust manifold through the high-pressure inlet duct. The low-pressure turbo is attached to the high-pressure turbo by a low-pressure inlet duct, which is linked to a connecting channel. A single actuator that is housed in the exhaust manifold creates a bypass that can opens the high-pressure inlet or close the connecting channel. Depending on what the engine load and speed is, the ECU guides the actuator—a single rotating spindle with discs corresponding to flanges on the high and low pressure sides—to isolate one of the two turbos. Isolating the turbos allow the respective inlets to be engineered for the best possible fluid dynamic performance. The setup should increase performance and decrease lag. There's no word on what car this setup will make an appearance on, but it will most likely be used in premium vehicles before trickling down to the rest of GM's vehicles. Related Video: News Source: GM Inside News, AutoGuide via GM Authority Cadillac Chevrolet GM Technology Sedan turbo patent engine turbocharging