1992 Chevrolet Blazer Silverado Sport Utility 2-door 5.7l on 2040-cars
Dunkirk, New York, United States
Vehicle Title:Clear
For Sale By:Private Seller
Engine:5.7L 350Cu. In. V8 GAS OHV Naturally Aspirated
Body Type:Sport Utility
Fuel Type:GAS
Interior Color: Blue
Make: Chevrolet
Model: Blazer
Trim: Silverado Sport Utility 2-Door
Drive Type: 4WD
Number of Cylinders: 8
Mileage: 168,000
Exterior Color: White
for sale 1992 fullsize chevy blazer
too many new parts to list
Chevrolet Blazer for Sale
- Chevy k5 blazer 6.2 diesel banks turbo dana 60 front axle(US $9,500.00)
- 1979 chevrolet blazer 79 chevy k5 blazer(US $9,500.00)
- 1970 chevy blazer
- Custom 1989 chevy k5 blazer full size lifted 4x4(US $20,000.00)
- 1987 k-5 blazer
- 1974 chevrolet blazer 4wd(US $18,900.00)
Auto Services in New York
Zoni Customs ★★★★★
Williams Toyota Scion ★★★★★
Watertown Auto Repair Svc ★★★★★
VOS Motorsports ★★★★★
Village Automotive Center ★★★★★
V J`s Car Care ★★★★★
Auto blog
Next-gen Chevy Silverado and GMC Sierra may use carbon fiber
Thu, Dec 7 2017It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck
Weekly Recap: Tesla loses money, still dominates the news
Sat, Aug 8 2015Some people get an inordinate amount of attention. In politics, it's Donald Trump. In football, it's Jim Harbaugh. And in the auto world, it's Elon Musk and his always-fascinating electric car company, Tesla Motors. General Motors is spending $877 million to upgrade a factory. So what! US auto sales are up. Who cares? Tesla has a metal snake that will recharge your car! So was the week in Tesla – er, the industry. Snarkiness aside, Tesla did dominate the news cycle, led by the announcement the company lost $184 million in the second quarter. Tesla also said it expects to deliver between 50,000 and 55,000 vehicles this year, and is preparing for a full launch of the Model X crossover in September. Musk also made news during the earnings call by simply not answering a question about ride sharing, leading to speculation Tesla could be considering its own operation. While the financials were the arguably the most important company news, reports of a Model S cyber hacking were more compelling fodder for Tesla followers. Researchers were able to attack the sedan and bring it to a stop, though they required access to the car first. Tesla says it already has deployed a remedy for the situation. On a lighter note, Tesla published a video of its metal charger prototype that autonomously uncoils like a snake to power up the company's vehicles, provoking plenty of humorous comments and comparisons. Watch it and decide for yourself. While some of this might seem trivial, much of Tesla's recent attention has been warranted. It's the first startup US automaker in decades to launch from nothing and actually gain traction in the market. Sure, Musk is a lightning rod and Tesla always seems to be in the spotlight. But amid all of the publicity, it easy to lose sight of the new reality: Tesla is a force. OTHER NEWS & NOTES 2016 Chevy Volt lights up 106 MPGe The Chevy Volt's vitals are looking healthier for 2016. The second-generation plug-in hybrid racks up a gaudy 106 miles per gallon equivalent, which is an increase of eight MPGe from the 2015 model. The new Volt can travel 53 miles on electricity, a significant jump from the 2015 Volt's 38-mile range. The new car also has a 420-mile total range when factoring in the capability of the gasoline engine, which is 40 miles greater than the current car offers.
GM recalls 8,500 Chevrolet Malibu models for rear suspension glitch
Mon, 04 Feb 2013According to a letter from General Motors to the National Highway Traffic Safety Administration, flaws in the build process of the 2013 Chevrolet Malibu have led to the recall of 8,519 cars. Units built between December 6, 2011 and January 15, 2013 may have been assembled with rear suspension cradles that had insufficient torque applied to certain bolts. That out-of-spec assembly could lead to issues ranging from slight noises to a loss of vehicle control.
The problem was first noticed in December of last year by a GM test fleet driver and eventually tracked back to the improperly torqued bolts on the suspension cradle assembled through July 2012 by a supplier located not too far from the Malibu's Detroit/Hamtramck Assembly Plant. Since an official NHTSA recall notice has not been issued yet, it isn't clear whether or not Detroit-built Malibus were the only ones affected (the 2013 Malibu is also built at GM's Fairfax Assembly Plant in Kansas City, Kansas). Dealers will fix the problem by inspecting vehicles for proper torque specs, retightening if not within specs and, in some cases, perform a rear-wheel alignment.