55 Chevy on 2040-cars

Auto blog

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck

GM trucks get hybrid versions, but you'll probably never see one

A few years ago, General Motors sold hybrid versions of its Chevy Silverado and GMC Sierra pickups. They weren't very good, using GM's old two-mode hybrid system that resulted in only negligible fuel economy gains. But GM's trying again, launching eAssist models of the 2016 Silverado and Sierra that are said to offer 2-mpg improvements in city, highway, and combined fuel economy ratings. Problem is, you probably won't be able to get one. Only 700 eAssist trucks will be made for the 2016 model year – 500 Silverados and 200 Sierras. When you consider that GM moved 824,683 examples of its light-duty pickups in 2015, this small run represents 0.08-percent of all Silverado/Sierra production, and GM says it "will monitor the market closely ... and adjust as appropriate moving forward." But that's not the only limitation. The eAssist trucks will only be sold through California dealers. For the Silverado, eAssist can only be optioned on the 1500 Crew Cab 1LT 2WD model, and for the Sierra, the fuel-saving technology is solely available on the 1500 SLT Crew Cab 2WD model with the SLT Premium Plus package. Granted, in terms of the Sierra, that means you get niceties like LED headlights and taillights, Apple CarPlay and Android Auto, Bose premium audio, heated seats and steering wheel, lane keep assist, and more. In the trucks, eAssist combines a small electric motor and 0.45-kWh battery pack with the pickups' 5.3-liter V8. GM estimates total output of 355 horsepower and 383 pound-feet of torque – no more horsepower than the non-eAssist trucks, but three more pound-feet of torque. GM says the eAssist trucks can tow up to 9,400 pounds, and the battery only adds 100 pounds to the trucks' weight. The electric motor provides 13 hp and 44 lb-ft of torque for a boost of acceleration off the line, or during passing. It also allows the engine to run in four-cylinder mode for longer periods of time. eAssist uses regenerative braking to help power onboard electrical systems, and adds start/stop to the powertrain. Finally, the so-equipped trucks have a six-percent improvement in aerodynamics, thanks to a soft tonneau cover and active grille shutters in the front fascia. Great news is, the eAssist option is relatively inexpensive, only costing $500. But good luck getting your hands on one.

GM recalls 8,500 Chevrolet Malibu models for rear suspension glitch

According to a letter from General Motors to the National Highway Traffic Safety Administration, flaws in the build process of the 2013 Chevrolet Malibu have led to the recall of 8,519 cars. Units built between December 6, 2011 and January 15, 2013 may have been assembled with rear suspension cradles that had insufficient torque applied to certain bolts. That out-of-spec assembly could lead to issues ranging from slight noises to a loss of vehicle control.
The problem was first noticed in December of last year by a GM test fleet driver and eventually tracked back to the improperly torqued bolts on the suspension cradle assembled through July 2012 by a supplier located not too far from the Malibu's Detroit/Hamtramck Assembly Plant. Since an official NHTSA recall notice has not been issued yet, it isn't clear whether or not Detroit-built Malibus were the only ones affected (the 2013 Malibu is also built at GM's Fairfax Assembly Plant in Kansas City, Kansas). Dealers will fix the problem by inspecting vehicles for proper torque specs, retightening if not within specs and, in some cases, perform a rear-wheel alignment.