1955 Chevy Bel-air 4-door Turquoise/white on 2040-cars

Auto blog

GM puts 3 million miles on hydrogen fuel cell test fleet

Have General Motors' hydrogen fuel-cell vehicles emitted enough water vapor over the past six-plus years to equal the steam coming out of Old Faithful? Not exactly, but GM has released a few figures related to the Project Driveway initiative it began in 2007. The numbers are impressive, if not quite of the geyser-spouting variety. In all, the General converted 119 Chevrolet Equinox SUVs to run on hydrogen, and those vehicles have just collectively surpassed the 3 million mile mark. And if you were waiting for us to tell you that the distance equals a half-dozen round trips between the earth and the moon, well, there you go. The better news is that the SUVs have combined to save almost 158,000 gallons worth of gas, and some of the vehicles have more than 120,000 miles on them. More than 5,000 drivers have participated in the project. GM reached that landmark about 10 months after it announced that it was working with Honda to accelerate the development of hydrogen fuel-cell powertrain technology. The two companies estimated last summer that it may have something to sell to the public as soon as 2020. For now, you can check out General Motors' press release below. GM Fuel Cell Fleet Tops 3 Million Miles Chevrolet Equinox fuel cell vehicles driven in real world reach milestone DETROIT – General Motors' fleet of fuel cell vehicles recently passed 3 million miles of hydrogen-powered, real-world driving. Some individual vehicles have accumulated more than 120,000 miles. By GM's estimate, using hydrogen to power these vehicles, the fleet has avoided 157,894 gallons of gasoline consumption. This specially equipped fleet of Chevrolet Equinox Fuel Cell vehicles are part of GM's 119-vehicle Project Driveway program, which launched in 2007. Since then, more than 5,000 drivers have provided feedback on the functionality and drivability of fuel cell technology. "Hydrogen fuel cell technology is an important part of GM's advanced propulsion portfolio and we continue to make substantial progress in furthering this technology," said Charlie Freese, executive director of GM's global fuel cell engineering activities. "These vehicles have operated through seven full winters and a wide range of environmental conditions, proving that fuel cells can meet the demands of real-world drivers." Last year, GM announced two fuel cell-related collaborations.

GM trucks get hybrid versions, but you'll probably never see one

A few years ago, General Motors sold hybrid versions of its Chevy Silverado and GMC Sierra pickups. They weren't very good, using GM's old two-mode hybrid system that resulted in only negligible fuel economy gains. But GM's trying again, launching eAssist models of the 2016 Silverado and Sierra that are said to offer 2-mpg improvements in city, highway, and combined fuel economy ratings. Problem is, you probably won't be able to get one. Only 700 eAssist trucks will be made for the 2016 model year – 500 Silverados and 200 Sierras. When you consider that GM moved 824,683 examples of its light-duty pickups in 2015, this small run represents 0.08-percent of all Silverado/Sierra production, and GM says it "will monitor the market closely ... and adjust as appropriate moving forward." But that's not the only limitation. The eAssist trucks will only be sold through California dealers. For the Silverado, eAssist can only be optioned on the 1500 Crew Cab 1LT 2WD model, and for the Sierra, the fuel-saving technology is solely available on the 1500 SLT Crew Cab 2WD model with the SLT Premium Plus package. Granted, in terms of the Sierra, that means you get niceties like LED headlights and taillights, Apple CarPlay and Android Auto, Bose premium audio, heated seats and steering wheel, lane keep assist, and more. In the trucks, eAssist combines a small electric motor and 0.45-kWh battery pack with the pickups' 5.3-liter V8. GM estimates total output of 355 horsepower and 383 pound-feet of torque – no more horsepower than the non-eAssist trucks, but three more pound-feet of torque. GM says the eAssist trucks can tow up to 9,400 pounds, and the battery only adds 100 pounds to the trucks' weight. The electric motor provides 13 hp and 44 lb-ft of torque for a boost of acceleration off the line, or during passing. It also allows the engine to run in four-cylinder mode for longer periods of time. eAssist uses regenerative braking to help power onboard electrical systems, and adds start/stop to the powertrain. Finally, the so-equipped trucks have a six-percent improvement in aerodynamics, thanks to a soft tonneau cover and active grille shutters in the front fascia. Great news is, the eAssist option is relatively inexpensive, only costing $500. But good luck getting your hands on one.

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck