1953 Chevrolet Bel Air Base Sedan 4-door 3.5l on 2040-cars

Auto blog

Chevy's 6.6-liter Duramax is pretty much all new

To say there's a heated battle in heavy-duty pickups is an understatement, with Chevrolet, Ford, and Ram constantly trading blows of increased torque, horsepower, and towing capacity. The latest salvo is the revised, more powerful turbo diesel 6.6-liter Duramax V8 in the 2017 Chevy Silverado. It has 910 pound-feet of torque, an increase of 145, putting it nearly level with the Ford Super Duty. Here's a closer look at where those gains come from. How exactly did Chevrolet add all that torque plus 48 horsepower? The automaker essentially took a fine-tooth comb to the entire engine. Chevy says it changed 90 percent of the V8, and the cumulative effect of those small changes adds up to big increases. As you might guess, the turbocharger is updated. The larger unit features electric actuation of the variable nozzle turbine (VNT), and what Chevy calls a double axle cartridge mechanism that separates the VNT moving parts from the housing. That helps with heat performance as well, with a claim that the exhaust side of the turbo can run continuously up to 1,436 degrees Fahrenheit. Helping that cause are six exhaust gaskets made of Inconel - an nickel alloy that contains chromium and iron – and upgraded stainless steel for the exhaust manifold. Despite having the same cast iron cylinder block, albeit with some minor enhancements, the engine has new cylinder heads, pistons, piston pins, connecting rods, and crankshaft, which have all been upgraded to handle 20 percent higher cylinder pressures. Alongside the increase in pressure, Chevrolet also increased the cylinder head's structure with a honeycomb design. The pattern features high-strength aluminum with dual layer water jackets that not only improve strength, but also optimize water flow for better cooling. For 2017, the cylinder head also benefits from integrated plenum that aids the engine in getting more air under heavy loads. The cylinder head isn't the only component to get a minor update, as the pistons have a larger diameter pin for improved oil flow. The same detailed improvements has been bestowed to the humble connecting rods (second in our hearts only to the inanimate carbon rod). The new design has the bolts oriented roughly 45-degrees to the rod instead of parallel. The angle split design, as it's called allows for easier passage through the cylinder.

Bob Lutz builds the case for a mid-engined Corvette

Rumors of a mid-engine Corvette are like automotive industry folklore at this point. Every once in a while, news pops up that it might be happening or is under development, but nothing actually ever comes to fruition as something people can actually buy. The latest spy shots strongly suggest a mid-engine 'Vette is in the cards, yet again, possibly for 2018. Now, an op ed by former General Motors executive (and definite performance car fan) Bob Lutz in Road & Track gives the inside scoop on the history of one of these proposals and lays out how to make it happen today. According to Lutz, the company's engineers believed the C6 ZR1 was at the limit for front-engine, rear-wheel drive performance in that package, and the only solution was to move the powerplant behind the driver. Lutz even got then CEO Rick Wagoner on board. The scheme made it at least as far as clay models for mid-engine versions of the 'Vette and Cadillac XLR. Eventually, a lack of money got in the way, though, bringing the project to an end. Lutz puts a lot of faith in GM's current leaders, especially Mary Barra and Mark Reuss. He thinks the chances of a mid-engine 'Vette happening this time are better than 50 percent. The model, rumored to be named Zora, could offer over 700 horsepower in an ultra lightweight body and be priced at about $120,000 to "suck the doors off everybody." Head over to Road & Track to get some insights from this highly respected and entertaining auto industry veteran. Related Video:

GM throttles back Chevy Malibu, Buick LaCrosse production over swollen inventories

As inventory of the Chevrolet Malibu and Buick LaCrosse continues to pile up, General Motors will be idling its Fairfax Assembly Plant for two weeks, according to Automotive News. This move comes about a month after the plant was shut down for three weeks in late December and early January for the same reason. As of January 31, the GM had a 94-day supply of Malibu stock while the LaCrosse was a little worse with a 117-day supply.
Just last week, GM announced that it would be investing $600 million in upgrading this plant, but it's unclear what future plans the company has in store for Fairfax considering slow sales of both the plant's models. We do expect a refreshed and more luxurious LaCrosse shortly and an early design update for the Malibu to be announced at some point this year, although we have had no official word as to when either will happen.