1953 Chevrolet 210 "tin Woody" Fuel Injected - Hot Rod Magazine Featured! on 2040-cars

Auto blog

Consumer Reports declares most and least loved cars [w/video]

Consumer Reports is crunching the numbers from its annual owner-satisfaction survey, and part of that process is finding out how attached drivers are to their cars. CR simply asks readers of models up to three years old if they would buy the same vehicle again in light of their entire ownership experience, and tallies the results. After looking at the responses for about 350,000 vehicles, it turns out that people really love a certain California-built, electrically powered luxury sedan. That's right, this year's the overall winner was the Tesla Model S with a whopping 98 percent of owners saying they would purchase another one (the Model S also won this award last year, with 99 percent satisfaction). The Chevrolet Corvette Stingray came in a close second with 95 percent of drivers hoping to park another one in their garage. A few models weren't quite so favored, though. The Nissan Versa Sedan was the least loved model among its owners; a mere 42 percent said that they would purchase another. The aging Jeep Compass didn't do much better, with just 43 percent of drivers willing to buy the softroader again. On average, about 70 percent of owners say they would buy their car again, and only four cars ranked below 50 percent in CR's findings. Check out the video above to see some of the winners and losers in a few of CR's categories. If you're a subscriber, you can check out the full list on its website. Related Gallery Consumer Reports Most Loved Cars 2014 Related Gallery Consumer Reports Least Loved Cars 2014 News Source: Consumer Reports - sub. req., Consumer Reports via YouTube Chevrolet Ford Mazda Mercedes-Benz Porsche Subaru Tesla Ownership Videos car ownership

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck

GM diesel pickups first to undergo extra EPA, CARB testing

The effects of Volkswagen's long-running diesel emissions evasion are starting to spill over to other automakers, but General Motors is taking things in stride. The 2.8-liter, four-cylinder Duramax in the 2016 Chevrolet Colorado and GMC Canyon is the first engine to get extra scrutiny by the Environmental Protection Agency and the California Air Resources Board, Automotive News reports. Rather than just the usual in-lab test, it's also being checked on the road. However, the extra evaluation shouldn't have any impact on when the trucks with his mill hit dealers later this fall. "We're in our final stages of the EPA certification, and our launch is on track," Chevy spokesperson Otie McKinley tells Autoblog. The four-cylinder diesel in the trucks makes 181 horsepower and 369 pound-feet of torque, and the automaker is touting low NOx production. In the announcement for the Colorado's specs, the company calls it "the cleanest diesel truck engine ever produced by General Motors." The tech includes exhaust gas recirculation to lower combustion temperatures and improve emissions. There's also a urea tank like on the bigger diesels for full-size trucks, and it gets refilled in time with oil changes. An indication on the instrument panel lets drivers know when that's needed, too. Even with the more demanding testing, the company doesn't seem too worried about the four-cylinder passing. "Part of our development process is on-road and off-road [laboratory] testing," Scott Yackley, Chevy Trucks assistant chief engineer, said to Automotive News. In the wake of the VW scandal, the EPA has pledged more rigorous testing. Before, on-road emissions evaluations were largely limited to heavy-duty vehicles, but the agency has decided to apply the checks more often to other models. There's also now greater cooperation with Canadian authorities.