Fully Loaded Black Diamond Ltz Hard To Find Low Mileage Super Clean Has Warranty on 2040-cars

Auto blog

GM recalls 8,500 Chevrolet Malibu models for rear suspension glitch

According to a letter from General Motors to the National Highway Traffic Safety Administration, flaws in the build process of the 2013 Chevrolet Malibu have led to the recall of 8,519 cars. Units built between December 6, 2011 and January 15, 2013 may have been assembled with rear suspension cradles that had insufficient torque applied to certain bolts. That out-of-spec assembly could lead to issues ranging from slight noises to a loss of vehicle control.
The problem was first noticed in December of last year by a GM test fleet driver and eventually tracked back to the improperly torqued bolts on the suspension cradle assembled through July 2012 by a supplier located not too far from the Malibu's Detroit/Hamtramck Assembly Plant. Since an official NHTSA recall notice has not been issued yet, it isn't clear whether or not Detroit-built Malibus were the only ones affected (the 2013 Malibu is also built at GM's Fairfax Assembly Plant in Kansas City, Kansas). Dealers will fix the problem by inspecting vehicles for proper torque specs, retightening if not within specs and, in some cases, perform a rear-wheel alignment.

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck

This 450-hp electric Lotus Evora is powered by Tesla and Chevrolet

When someone mentions an electric Lotus, the first thing that comes to mind is the Tesla Roadster, the California-based automaker's first vehicle. That car started life as an Elise before being heavily massaged and adapted by Tesla's engineers. In a similar spirit, the people at Onpoint Dyno are close to finishing Blue Lightning, a track-ready all-electric Lotus Evora. Blue Lightning uses a Tesla drive unit and a Chevrolet Volt battery pack, both mounted in the middle in place of the Evora's 3.5-liter Toyota V6. It's putting down about 450 horsepower at the wheels. The car was built for time attack sessions, so power is fed through custom forged wheels and super sticky Pirelli PZero Trofeo R tires, the same ones found on the last Chevrolet Camaro Z/28. There is a custom digital instrument cluster in place of the Lotus gauges. There's also a regen paddle on the left side of the steering wheel. With a full charge, Blue Lighting should go about 120 miles. While the car runs under its own power, it's only about 90 percent complete. It has no power steering, no firewall in between the seats and the motor and battery pack, no A/C, and a large hole where the shift lever used to be. Other final touches include fine-tuning the brakes and suspension. There is also a custom rear bumper coming that should make it look more like the new Lotus Evora 400. Onpoint Dyno expects the car to hit the track in the next month or so. Related Video: