2009 Cadillac Sts on 2040-cars

Auto blog

GM faces possible class action lawsuit over 8-speed transmission

General Motors has been hit with a class-action lawsuit from owners who allege the eight-speed automatic transmission found in several rear-wheel-drive Chevrolet, Cadillac and GMC models between the 2015 and 2019 model years has a defect that causes the vehicles to hesitate and jerk when accelerating or slowing down. The lawsuit was posted to ClassAction.org and spotted by GM Authority. Problems with GM's Hydra-Matic 8L90 and 8L45 transmissions have been well-documented on Internet forums and via complaints filed with the National Highway Traffic Safety Administration, with many reporting damage to their vehicles. The lawsuit was first filed in December in U.S. District Court for the Southern District of Florida but appears to have been transferred recently to New York. Autoblog sought comment from Theodore Leopold, the lead attorney for the plaintiffs. "These transmissions have a common defect," the complaint reads. "Drivers attempting to accelerate or decelerate their cars feel a hesitation, followed by a significant shake, shudder, jerk, clunk, or 'hard shift' when the vehicle's automatic transmission changes gears." The problem also occurs when the vehicles accelerate in a single gear, without shifting, the plaintiffs allege. "Drivers have reported that the shift is sometimes so violent, they feel as though they have been hit by another vehicle." The problem is believed to center on the transmission, torque converter or both. The complaint says it causes undue friction, causing hydraulic systems and gears to function improperly and sometimes leaves metal shavings throughout the transmission, leading to costly repairs and replacement of parts or the entire transmission. It says GM has known about the problems since shortly after it introduced the transmissions, and has issued 13 technical service bulletins, none of which have resolved the problem. GM declined to comment on the lawsuit. The plaintiffs say GM should have warned consumers about the issues and covered repairs under each vehicle's three-year/36,000-mile bumper-to-bumper warranty. They're seeking statewide classes in at least six states: California, Florida, Illinois, New York, Oklahoma and Texas.

2016 Cadillac ATS-V First Drive [w/video]

If you get hot and bothered for hot-rodded sedans and coupes, you probably know that Germans have long dominated that cutthroat scene. For years, the Audi RS/BMW M/Mercedes-AMG triumvirate has ruled the microcosm of grunty, mid-level luxury cars. But a funny thing happened when Cadillac's first V car hit the market in 2004. Since the CTS-V crashed the high horsepower party, German tuning houses started thinking less about the "Daddy's Caddy" stereotypes and more about the next imminent threat – in this case, the inevitable high-horsepower spinoff of the smaller, nimbler Cadillac ATS. The standard ATS' defense against the German triad hasn't been triumphant so far (GM's Michigan plant was idled for three weeks in 2014 due to excess inventory), but the souped-up 2016 Cadillac ATS-V presents a fresh bid to put the Teutonic competition on alert. The ATS-V's flared bodywork and quad exhaust pipes offer bits of visual shock and awe, but significant hardware upgrades back up the go-fast looks. Front and center is a twin-turbocharged, 3.6-liter V6 with reworked internals including a charge-air cooler, titanium connecting rods, and titanium-aluminide turbines. The new engine produces 464 horsepower and 445 pound-feet of torque, up a staggering 262 hp and 173 lb-ft compared to a base, four-cylinder ATS. Those output figures eclipse the BMW M3/M4 (425 hp, 406 lb-ft) and Audi RS5 (450 hp, 317 lb-ft), but lag slightly behind the V8-powered Mercedes-AMG C63 (476 hp, 479 lb-ft), and more so the C63 S (503 hp, 516 lb-ft). The chassis benefits from several structural braces, most notably a shear panel intended to boost front-end stiffness. Extra poundage from the add-ons are minimized through lighter-weight materials – in the case of the shear panel, stamped aluminum. Cadillac says though it intended to make the ATS the quickest car in its segment (stated 0-60 mph times between 3.8 and 3.9 second virtually match the BMW M4 and Mercedes-AMG C63 S' 3.9 figure), the development team says they also focused on subjective qualities like turn-in quickness and steering response. As such, toe links have been replaced with ball joints, mounts have been retuned, and reworked magnetic damping offer greater responsiveness. Six suspension bushings have been stiffened and ten have been completely redesigned, and the Performance Traction Management system that tames beasts like the Corvette Z06 and Camaro ZL1 also helps lay down power in the ATS-V.

Our favorite mid-engine Corvette theories and rumors

The mid-engine Corvette! We just saw blurry photos through the foliage, and are hearts are all aflutter because it means that this car is real. And it's the most " never before" Corvette since 1984. Which leads us to all kinds of wacky theories and speculation. Everybody knows something or heard from a guy. None of those guys (or gals) from GM are talking to Autoblog, to be clear. But that won't stop us from stirring the pot. Let's go over a few point-by-point. The pushrod engine will be replaced by an overhead-cam V8 Car and Driver has repeatedly reported that an overhead-cam engine will come after the mid-engine Corvette's debut with an old-school pushrod. We've heard the same thing firsthand, albeit from a source with no connection to the development of the Corvette or powertrain. "At some point two valves can't pass future emissions regulations," said the guy we know. While the pushrod engine is compact, the design makes it difficult - if not impossible - for sophisticated variable valve timing (and lift) systems that control combustion with more precision. Hasty conclusion: The pushrod engine has a finite life in front of it. This one's a lock, it's a just a matter of when. Bowling Green's new paint shop is really the mid-engine assembly line Credit to Reddit for this one. Like we said, everybody knows a guy. But let's look deeper. The new paint facility costs $439 million dollars and adds 450,000 square feet, almost half the size of the existing plant. Plus GM announced another $290 million in upgrades at Bowling Green Assembly. That sure sounds like a lot of money, but you can actually spend that much on a paint booth. Porsche spent 500 million Euros (about $561 million dollars) to add the Macan assembly to its Leipzig, Germany plant in 2014. Chrysler shelled out $850 million for a paint shop in Sterling Heights, Michigan. GM spent $600 million for a new paint shop at the Fairfax (Kansas City) plant. Honda, on the other hand, is working on a thrifty $210 million project in Marysville, Ohio that includes a 300,000 square foot expansion, and the low-volume Acura NSX facility only cost $70 million. Hasty conclusion: The square footage and cost could easily mean a new assembly line instead of (or in addition to) a paint line. And if the NSX plant was really that cheap, GM could have hidden a similar sum in its existing announcements.